Electrical System

Connector Assignments

~5min read

Navigation Connector Assignment, 7T2

Information Electronics Control Module 1 -J794-

Information Electronics Control Module 1 -J794-

1 - DAB Connection from Antenna Amplifier 3 -R112-, Digital Radio Antenna -R183-, QV3

- SAT connection from Roof Antenna -R216-, Satellite Antenna -R170-, only USA and QV8

2 - GPS Connection from the Roof Antenna -R216-

3 - Connection Block with Four Multi-Pin Connectors

4 - MOST Bus

5 - 4-Pin Connector -T4z- to the External Audio Source Connection -R199-

6 - 4-Pin Connector -T4df- to the Front Information Display Control Head -J685-

7 - AM/FM/FM2 Antenna Connection

Note

Unlisted connector terminals are not assigned.

3 - Connection block with four multi-pin connectors

A - 8-Pin Connector -T8e-

1 - Right rear speaker (+)

2 - Right front speaker (+)

3 - Left front speaker (+)

4 - Left rear speaker (+)

5 - Right rear speaker (-)

6 - Right front speaker (-)

7 - Left front speaker (-)

8 - Left rear speaker (-)

A91-11645

B - 12-Pin Connector -T12c-

1 - Data from Multimedia System Control Head -E380-

2 - Res BT Multimedia System Control Head -E380-

3 - Not Assigned

4 - Microphone input (+) from Microphone Unit in Front Roof Module -R164-, Left Front Microphone -R140-

5 - CVBS cable (-) for the Rearview Camera System Control Module -J772-

6 - Not Assigned

7 - Data to the Multimedia System Control Head -E380-

8 - Wake UP Multimedia System Control Head -E380-

9 - Res HU to the Multimedia System Control Head -E380-

10 - Not Assigned

11 - CVBS cable (+) for the Rearview Camera System Control Module -J772-

12 - Microphone input (-) for the Microphone Unit in Front Roof Module -R164-, Left Front Microphone -R140-

A91-11645

C - 12-Pin Connector -T12e-

All pins are connected to the External Audio Source Connection -R199-.

1 - LF-In ground

2 - Right LF-In

3 - USB, +5 V

4 - USB, ground

5 - iPod, ACC Power

6 - Detect

7 - Left LF-In

8 - LF-In ground shielding

9 - CVBS cable (+)

10 - CVBS cable (-)

11 - iPod data

12 - iPod data

A91-11645

D - 8-Pin Connector -T8f-

9 - Subwoofer -R211-

10 - Center Speaker -R208-

13 - Subwoofer -R211-

14 - Center Speaker -R208-

17 - Terminal 31

18 - Terminal 30

A91-11645

E - 12-Pin Connector -T12d-

7 - Ring-break Diagnostic Cable

A91-11645

4 - MOST Bus

1 - Output

2 - Input

A91-11851

5 - 4-Pin Connector -T4z-

All pins are connected to the External Audio Source Connection -R199-.

1 - D (+)

2 - iPod recognized

3 - D (-)

4 - Ground

A91-12091

6 - 4-Pin Connector -T4df-

All pins are connected to the Front Information Display Control Head -J685-.

1 - LVDS (-)

2 - LIN

3 - LVDS (+)

4 - Ground

A91-12091

Chip Card Reader Control Module -J676- Connector Assignment, through MY 2014

Chip Card Reader Control Module -J676-

Note

Unlisted connector terminals are not assigned.

32-Pin Connector -T32p-

1-16 - to the Traffic Data Antenna -R173-

17 - VICS data wire to the Information Electronics Control Module 1 -J794-

19 - VICS data wire to the Information Electronics Control Module 1 -J794-

21 - Switch-on signal to the Information Electronics Control Module 1 -J794-

22 - Terminal 30

23 - ETC data to the Information Electronics Control Module 1 -J794-

25 - ETC data from the Information Electronics Control Module 1 -J794-

28 - Terminal 31

A91-11927

Chip Card Reader Control Module -J676- Connector Assignment, from MY 2015

Chip Card Reader Control Module -J676-

1 - 5-Pin Connector -T5br- to the front External Audio Source Connection -R199-, USB quantity: 2, AUX IN

2 - 10-Pin Connector - T10bk-

3 - Connection from the Close Range Communication Antenna -R269-

A91-12293

1 - 5-Pin Connector -T5br-

All pins are connected to the External Audio Source Connection -R199-.

1 - Data (+)

2 - USB, +5 V

3 - Data (-)

4 - USB, ground

5 - Ground Shielding

A91-12098

10-Pin Connector - T10bk-

1 - Supply (+) Traffic Data Antenna -R173-

2 - Supply (-) Traffic Data Antenna -R173-

3 - VICS data wire to the Traffic Data Antenna -R173-

4 - VICS data wire from the Traffic Data Antenna -R173-

5 - Not Assigned

6 - Not Assigned

7 - Diagnosis 1 Traffic Data Antenna -R173-

8 - Diagnosis 2 Traffic Data Antenna -R173-

9 - Terminal 30

10 - Terminal 31

A91-11317

Chip Card Reader Control Module, Removing and Installing

The Chip Card Reader Control Module -J676- is located inside the glove compartment.

Removing

- Turn off the ignition and all electrical consumers and remove the ignition key.

- Open the glove compartment.

- Remove the chip card.

- Slide the Chip Card Reader Control Module -J676--1- back until it can be removed from the trim.

- Remove the clip -4-.

- Release and disconnect the connector -3- from the Chip Card Reader Control Module -J676--1-.

A91-11779

Installing

- Connect the connector -3- and then push the clip -4- through the opening.

- Make sure that all of the tabs -2- on the Chip Card Reader Control Module -J676--1- engage into the trim.

A91-11779