Electrical System

Ground Cable with Battery Monitoring Control Module -J367-, Removing and Installing

~4min read

Ground Cable with Battery Monitoring Control Module -J367-, Removing and Installing, Vehicles without High Voltage System

Removing

- Turn off the ignition.

- Lift the luggage compartment floor covering by the handle and fold it forward.

- Remove the vehicle tools.

- If equipped, remove the spare tire well trim. Refer to → Body Interior; Rep. Gr.70; Luggage Compartment Trim Panels; Spare Wheel Well Trim, Removing and Installing.

- Open the cover -1- over the battery negative terminal.

- Loosen the nut -2- several turns and remove the battery ground cable terminal from the battery negative pole.

- Disconnect the connector -3-.

- Remove the nut -5- and remove the ground cable -6- with the Battery Monitoring Control Module -J367--item 4-.

Installing

Install in reverse order of removal. Note the following:

- Connect the battery.

A27-10304

Ground Cable with Battery Monitoring Control Module -J367- for the Battery -A-, Removing and Installing, Vehicles with High Voltage System

DANGER!

Damaged high voltage components may produce dangerously high voltage.

Note the following when working near high voltage components and cables:

  • Do not use tools that have sharp edges, that are used for cutting or shaping, or that generate heat, such as welding, soldering, hot air or thermal adhesive equipment.
  • Inspect the high voltage components in the area where the work will be performed before starting the procedure.
  • Perform a visual inspection of the Electric Drive Power and Control Electronics -JX1-, the Electro-Drive Drive Motor -V141-, the Electrical A/C Compressor -V470- and the high voltage cables when working inside the engine compartment.
  • Perform a visual inspection of the high voltage cables and the covers when working on the floor panel.
  • Perform a visual inspection of the high voltage cables and the electro-box with the High Voltage System Maintenance Connector -TW- when working in the rear of the vehicle.
  • Perform a visual inspection of all of the potential equalization cables.

Note the following when performing the visual inspection:

  • None of the components may display any exterior damage.
  • The high voltage cable insulation and the potential equalization cables may not be damaged.
  • The high voltage cables may not be deformed in any way.
  • Each high voltage component muss be labeled with a red warning label.

Removing

- Remove the luggage compartment floor. Refer to → Body Interior; Rep. Gr.70; Luggage Compartment Trim Panels; Luggage Compartment Floor Panel, Removing and Installing.

- Remove the battery exhaust air guide. Refer to → Heating, Ventilation, and Air Conditioning; Rep. Gr.87; Battery Cooling Module.

- Loosen the nut -1- several turns and remove the battery ground cable terminal from the battery pole.

- Disconnect the connector -2-.

- Remove the nut -5- and remove the ground cable -4- with Battery Monitoring Control Module -J367--item 3-.

Installing

Install in reverse order of removal. Note the following:

- Connect the battery.

A27-10412

Ground Cable with Battery Monitoring Control Module 2 -J934- for the Auxiliary Battery -A1-, Removing and Installing, Vehicles with High Voltage System

DANGER!

Damaged high voltage components may produce dangerously high voltage.

Note the following when working near high voltage components and cables:

  • Do not use tools that have sharp edges, that are used for cutting or shaping, or that generate heat, such as welding, soldering, hot air or thermal adhesive equipment.
  • Inspect the high voltage components in the area where the work will be performed before starting the procedure.
  • Perform a visual inspection of the Electric Drive Power and Control Electronics -JX1-, the Electro-Drive Drive Motor -V141-, the Electrical A/C Compressor -V470- and the high voltage cables when working inside the engine compartment.
  • Perform a visual inspection of the high voltage cables and the covers when working on the floor panel.
  • Perform a visual inspection of the high voltage cables and the electro-box with the High Voltage System Maintenance Connector -TW- when working in the rear of the vehicle.
  • Perform a visual inspection of all of the potential equalization cables.

Note the following when performing the visual inspection:

  • None of the components may display any exterior damage.
  • The high voltage cable insulation and the potential equalization cables may not be damaged.
  • The high voltage cables may not be deformed in any way.
  • Each high voltage component muss be labeled with a red warning label.

Removing

- Remove the luggage compartment floor. Refer to → Body Interior; Rep. Gr.70; Luggage Compartment Trim Panels; Luggage Compartment Floor Panel, Removing and Installing.

- Loosen the nut -1- several turns and remove the battery ground cable terminal from the battery pole.

- Disconnect the connector -2-.

- Remove nut -4- and ground cable -3- with the Battery Monitoring Control Module 2 -J934--item 5-.

Installing

Install in reverse order of removal. Note the following:

- Connect the battery.

A27-10411