Transmission

Transmission Control

~4min read

Component Location Overview - Transmission Control

Diagnostic Connection

Installed location: the diagnostic connection for the Vehicle Diagnostic Tester in inside the footwell on the driver side.

N01-0592

All Wheel Drive Control Module -J492- in the A4 Sedan, A5 Coupe and the A5 Cabriolet

Component location: The All Wheel Drive Control Module -J492--A- is located in the spare wheel well in front of the battery.

A39-10392

All Wheel Drive Control Module -J492- in the A4 Avant

Component location: The All Wheel Drive Control Module -J492--1- is in the luggage compartment on the right in front of the spare wheel well.

A39-10444

All Wheel Drive Control Module -J492- in the A5 Sportback

Installed location: The All Wheel Drive Control Module -J492--1- is in the rear right wheel housing under the luggage compartment side trim. Refer to → Body Interior; Rep. Gr.70; Luggage Compartment Trim.

A39-10445

All Wheel Drive Control Module -J492- in the Audi A6/A7

Component location: The All Wheel Drive Control Module -J492--A- is located on the right in the spare wheel well.

A97-11328

All Wheel Drive Control Module -J492- in the A8

Component location: The All Wheel Drive Control Module -J492--1- is located on the left in the spare wheel well.

A39-10446

All Wheel Drive Control Module -J492-, Removing and Installing

Note

  • All Wheel Drive Control Module -J492- component location. Refer to → Chapter "Component Location Overview - Transmission Control".
  • Removing and installing is on the A4 Sedan.
  • The ignition is off.

- Remove the luggage compartment floor covering.

- Remove the covering and the vehicle tools mount.

- Remove the All Wheel Drive Control Module -J492--A- from the bracket -C-.

- Disconnect the connector -B- from the All Wheel Drive Control Module -J492-.

- Install the All Wheel Drive Control Module -J492- in reverse order of removal.

  • If the All Wheel Drive Control Module -J492- was replaced then additional work is necessary. Refer to → Chapter "All Wheel Drive Control Module -J492-, Additional Work after Replacing".
A39-10392

All Wheel Drive Control Module -J492-, Additional Work after Replacing

Note

Only perform the additional work only if the All Wheel Drive Control Module -J492- was replaced.

- Connect the Vehicle Diagnostic Tester and turn on the ignition.

- Select the function 22 - All Wheel Drive (AWD) Electronics in the vehicle diagnostic tester under Guided Functions in the directory 22- Replacing Control Module.

  • Follow all the instructions given by the Vehicle Diagnostic Tester exactly.

With the vehicle diagnostic tester the installed rear final drive is "adapted" on the All Wheel Drive Control Module -J492-.

Note

A system check will take place when the 22 - Control Module, Replacing function is complete. If malfunctions appear, then use "Guided Fault Finding" to correct them.

Special Tools

Special Tools

Special tools and workshop equipment required

  • Puller -VW391-
  • Slide Hammer-Complete Set -VW771-
  • Additional Part for VW771 -VW771/37-
  • Thrust Piece -T40112-
  • Retainer -3028-
  • Seal Driver-Frt Wheel Bearing -3143-
  • Puller -T10037-
W00-0976
  • Tensioning Strap -T10038-
W00-1005
  • Puller -T10055-
W00-10115
  • Wheel Hub Support -T10149-
W00-1297
  • Hex Ball Socket -T10058-
W00-1006
  • Counterhold Tool Touareg V10 -T10172-
  • Adapter -T10172/5- (M8 Bolts)
  • Adapter -T10172/6- (M10 Bolts)
W00-10637
  • Adapter -T10235-
W00-10059
  • Socket 4 mm -T10370-
W00-10582
  • Thrust Piece -T10380-
W00-10610
  • Thrust Piece -T40108-
W00-10395
  • Thrust Piece -T40109-
W00-10396
  • Thrust Piece -T40110-
W00-10397
  • Thrust Piece -T40111-
W00-10398
  • Socket XZN 12 -T40154-
W00-10575
  • Socket 27 mm -T40218-
W00-10779
  • Assembly Tool -T40222-
  • Assembly Tool -T40222/1-
W00-10809
  • Assembly Tool -T40247-
  • Guide Sleeve -T40247/1-
W00-10946
  • Flanging Tool -T40261-
W00-10986
  • Hose Clamp Pliers -VAG1275-
W00-0451
  • Engine-Transmission Jack -VAG1383 A- with Universal Transmission Support -VAG359/2-.
W00-0120
  • Friction Gauge -VAS6222-
W00-10007
  • Charging Device for Haldex Coupling 2 -VAS6291- or Charging Device for Haldex Coupling 2 -VAS6291A-
W00-10656
  • Inductive Heater -VAS6414-
W00-10814
  • Needle Bearing Drift -VW295-
W00-0125
  • Needle Bearing Drift -VW295A-
W00-0126
  • Thrust Plate -VW401-
W00-0135
  • Thrust Plate -VW402-
W00-0136
  • Punch -VW407-
W00-0014
  • Punch -VW408A-
W00-0022
  • Punch -VW412-
W00-0139
  • Thrust Pad 16.5/28 mm Diameter -VW431-
W00-0142
  • Support Channels -VW457-
W00-0146
  • Slide Hammer-Complete Set -VW771-
W00-0018
  • Transmission Support -VW785/1B-
W00-0803
  • -3-Separating Tool 22 to 75 mm, for example, Kukko Separating Tool 12-75 mm -17/1-
  • -3-Kukko Separating Tool 22-115 mm, for example, Kukko Separating Tool 22-115 mm -17/2-
W00-0633
  • -1-2-Arm Puller Kukko -20/10-
W00-0634
  • Sleeve -32 - 119-
W00-0647
  • Sleeve -40 - 20-
W00-0013
  • Sleeve -40 - 21-
W00-0116
  • Seal Press Sleeve -2003/1- from the Seal Installer -2003-
W00-0354
  • Thrust Pad -3062-
W00-0581
  • Alignment Fixture-4W Dr. Shaft -3139-
W00-0948
  • Press Support-R and R Ball Joints -3146-
W00-0084
  • Press Tube -3345-
  • Not illustrated:
  • Thrust Piece -T40221-
  • Oil Filling Adapter -VAS6291/2- or Oil Filling Adapter -VAS6291/3-
W00-0311

Revision History

DRUCK NUMBER: A005A502721

Revision History