DCT(Dual Clutch Transmission) System

DCT(Dual Clutch Transmission) Repair procedures

31steps
~196min
5/5difficulty
2special tools
0102030405011.89N·mlb·ft
Tightening torque found on this page
Done 0 of 31

Removal

  1. Shut off the high voltage circuit.

    (Refer to Automatic Transaxle System - "High Voltage Shut-off Procedure")

  2. Drain the coolant of hybrid cooling system.

    (Refer to Hybrid Motor System - "Coolant")

  3. Remove the hybrid power control unit (HPCU) assembly.

    (Refer to Hybrid Control System - "Hybrid Power Control Unit")

  4. Disconnect the TCM connector (A) and ECM connector (B).

  5. Remove the TCM (A) and ECM (B).

    Tightening torque : 9.8 - 11,8 N·m

  6. Remove the HPCU tray (C) after removing the nut (A) and wiring mounting clips (B).

    Tightening torque :

    (A) 10.8 - 13,7 N·m

    (C) 21.6 - 24 N·m

  7. Disconnect the gear actuator motor connector (A) and gear actuator solenoid connector (B).

  8. Disconnect the connectors (A, B, C).

    (A) : Clutch actuator connector

    (B) : Input speed sensor connector

    (C) : Inhibitor switch connector

  9. Disconnec the hybrid drive motor connector (A) and loosen the wiring bracket mounting bolt (B).

    Tightening torque : 9.8 - 11,8 N·m

  10. Remove the ground (A).

  11. Loosen the wiring bracket mounting bolt (A) and TCM ground mounting bolt (B).

    Tightening torque : 9.8 - 11,8 N·m

  12. Remove the shift cable after loosening the bolts (B) and nut (A).

    Tightening torque :

    (A) 9.8 - 14,7 N·m

    (B) 19.6 - 26 N·m

  13. Separate the hybrid motor cooler upper hose and remove the bracket (B).

    Tightening torque : 9.8 - 11,8 N·m

  14. Loosen the hybrid drive motor upper mounting bolts (A).

    Tightening torque : 39.2 - 48 N·m

  15. Remove the covers (A).

  16. Assemble the engine support fixture on the engine room.

    (Refer to Special Service Tools - "Engine support fixture assembly drawing")

  17. Remove the cover (A).

  18. Support the transmission on a jack.

  19. Remove the transmission mounting bracket bolts (A).

    Tightening torque : 88.3 - 108 N·m

  20. Remove the transmission support bracket (A).

    Tightening torque : 58.9 - 78 N·m

  21. Remove the sub frame.

    (Refer to Suspension System - "Sub Frame")

  22. Remove the drive shaft assembly.

    (Refer to Driveshaft and Axle - "Front Driveshaft")

  23. Remove the CKP sensor loosening a bolt (A) and then loosen the heater pump bracket bolts (B).

    Tightening torque :

    (A) 7.8 - 11,8 N·m

    (B) 17.7 - 22 N·m

  24. Remove the roll rod support bracket (A).

    Tightening torque : 49.0 - 69 N·m (5.0 - 7.0 kgf·m, 36.2 - 50.6 lb·ft

  25. Disconnect the engine clutch actuator connecor (A).

  26. Saparate engine clutch actuator hose (A) and motor cooler lower hose (B).

  27. Loosen the transmission lower mounting bolts (A, B) after supporting the transmission safely on a jack.

    Tightening torque :

    (A) 39.2 - 48 N·m

    (B) 48.1 - 54 N·m

  28. After separating the transmission from the engine, remove the transmission by lowering the jack slowly.

  29. Remove the hybrid drive motor assembly from the DCT assembly.

    (Refer to Hybrid Motor System - "Hybrid Drive Motor Assembly")

Installation

  1. Install in the reverse order of removal.

  2. Observe each separate procedure below for reinstallation or replacement with a new dual clutch transmission.