Body Electrical System

Description and operation

12steps
~72min
3/5difficulty
Done 0 of 12

Description

System block diagram

Components of LDWS

No Item Function Position
1 LDWS Unit
  1. Lane Departure Warning System (LDWS) : Detects the current driving lane ahead and engages warning function if the vehicle is in danger of departing from the current driving lane.

  2. High Beam Assist (HBA) : Detects the headlamp light from the oncoming vehicle and taillamp light from the vehicle ahead and turns ON/OFF the high beam.

  3. Speed Limit Information Function (SLIF)

    : Detects traffic signs by using the camera and displays the speed limit by using the map data from navigation.

Windshield Glass
2 LDWS Switch LDWS On/Off Switch Crash Pad (Left)
3 Multifunction Switch HBA On/Off Switch (MF : Auto mode) Steering Wheel
4 User Setting Menu SLIF On/Off, Menu Cluster menu
5 Cluster/Buzzer SLIF/LDWS Warning Cluster

Camera unit of the LDWS processes the following functions using the video signal input.

  • Detects and analyzes the current driving lane

  • Detects the light from foregoing vehicle and oncoming vehicle

  • Detects and analyzes the status of foregoing vehicle and oncoming vehicle, and sets off warning sound (or message) for driver if necessary.

  • Transmits the information via high speed CAN communication

  1. Lane Departure Warning System (LDWS) unit

    Lane Departure Warning System (LDWS) High Beam Assist (HBA)
    Lane Departure Warning When detecting light from vehicle in front

    Speed Limit Information Function (SLIF) Automatic Emergency Braking (AEB)
    Speed Limit Information Vehicle and pedestrian detection

    The lane departure warning system is a convenient feature that detects the lanes ahead by using the camera image and vehicle signal data to alarm the driver in case the vehicle deviates from the lane. It consists of the camera unit used to detect the lane by analyzing the camera image input signal.

    The sensor module that processes screen image by sensing the lanes ahead on the camera unit, senses the lanes and analyzes the key parameters, i.e. vehicle center offset, road width, vehicle driving angle and road curvature, to keep to the lane. The following procedure is the lane detecting process through screen image processing.

    1. Senses the land by inputting the road image.

    2. Filters and calculates by magnifying the lane.

    3. Extracts the lane candidate point. (The constituent points are assumed as a lane.)

    4. Senses the land by means of candidate points.

  2. LDWS Operation process

    When the LDWS switch is pressed, the operation state of the lane departure warning system is displayed at the center of the cluster as long as the LDWS lamp is turned on.

    The specific classification of the displays is shown in the following table.

    Category Operation LDWS Display and Alert
    Control
    (Button)
    On LDWS On
    Off LDWS Off
    Operation Status Cluster indicator
    Operation Condition Activates if vehicle speed exceeds set speed with LDWS ON.

    [Start : 60 km/h ^]
    [Stop : 55 km/h v]

    ? Lane departure warning is not activated if turn signal or hazard lamp is ON.
  3. High Beam Assist

    Category Operation LDWS Display and Alert
    Control
    (Button)
    On If High Beam switch is turned ON (push-return) while the Multifunction Switch is set to Auto.
    HBA On + Low beam
    HBA On + High beam
    Off If High Beam switch is activated again while the Multifunction switch is NOT set to Auto or when HBA is ON.
    Operation Status Cluster display
    Operation Condition Activates if vehicle speed exceeds set speed with HBA ON.

    [Start: 45 km/h ^]
    [Stop: 35 km/h v]

    ? Activates only if Multifunction switch is set to Auto and Low Beam is ON.

LDWS ON/OFF switch (A)

When the LDWS switch is pressed, the LDWS is activated as long as the LDWS lamp is turned on. When the switch is pressed again, the LDWS is turned off and the display lamp is turned off.

High Beam Auto Control Switch: High Beam Auto Control System is turned ON if the Multifunction Switch Light SW is set to AUTO, and the Light SW is set to High Beam position (Pushed).

  • If the Light SW is not set to AUTO, or to High Beam position, the High Beam Auto Control System is turned OFF.

Alarm of LDWS

  1. Visual alarm : The lane toward the direction of departure blinks in "amber".

Operating conditions of LDWS

The operating conditions of LDWS are as below.

  1. The LDWS switch is turned "ON". The LDWS lamp on the instrument panel is turned on when the switch is on.

  2. LDWS function is set and the vehicle speed exceeds 60 km/h.

    The alarm stops momentarily when the vehicle speed falls below 60 - 55 km/h and restarts if the vehicle speed is over 60 km/h.

  3. If the driver operates the left or right turn signal lamps to show the intention of lane change, the alarm will be deactivated regardless of the direction of lane departure.

    The lane departure alarm function restarts 2 seconds after switching off the left or right turn signal lamps. The alarm is deactivated while operating the hazard lamps.

  4. Switch on the turn signal lamp before changing the lanes. Arbitrary change of lanes without operating the turn signal to the driving direction will generate alarm.

  5. When more than 40% of the vehicle body has crossed the lane, the alarm is released by sensing departure for lane change.

  6. The lane departure alarming is not made when the vehicle drives at the center of the lane.