Driveshaft and axle
Specifications
In this manual: Driveshaft and axle
~2min read
Specification
| Engine | Joint type | Max. permissible angle | ||
| Outer | Inner | Outer | Inner | |
| 1.6 GDI KAPPA | BJ#24 | VTJ#24 | 46.5° | 23° |
Tightening Torques
| Items | N·m | kgf·m | lb·ft | |
| Front | Wheel nut | 107.9 - 127.5 | 11.0 - 13.0 | 79.6 - 94.0 |
| Driveshaft caulking nut | 274.6 - 294.2 | 28.0 - 30.0 | 202.5 - 217.0 | |
| Strut assembly lower mounting bolt | 156.9 - 176.5 | 16.0 - 18.0 | 115.7 - 130.2 | |
| Wheel speed sensor mounting bolt | 8.8 - 13.7 | 0.9 - 1.4 | 6.5 - 10.1 | |
| Brake disc mounting screw | 4.9 - 5.8 | 0.5 - 0.6 | 3.6 - 4.3 | |
| Hub assembly mouning bolt | 88.3 - 107.9 | 9.0 - 11.0 | 65.1 - 79.6 | |
| Inner shaft bearing brakcet bolt | 49.0 - 63.7 | 5.0 - 6.5 | 36.2 - 47.0 | |
| Lower arm ball joint mounting bolt | 98.0 - 117.6 | 10.0 - 12.0 | 72.3 - 86.7 | |
| Tie rod end ball joint nut | 78.4 - 98.0 | 8.0 - 10.0 | 57.8 - 72.3 | |
| Stabilizer link | 98.0 - 117.6 | 10.0 - 12.0 | 72.3 - 86.7 | |
| Rear | Wheel nut | 107.9 - 127.5 | 11.0 - 13.0 | 79.6 - 94.0 |
| Brake caliper mounting bolt | 78.4 - 98.0 | 8.0 - 10.0 | 57.8 - 72.3 | |
| Brake disc mounting screw | 4.9 - 5.8 | 0.5 - 0.6 | 3.6 - 4.3 | |
| Hub assembly mouning bolt | 88.3 - 107.9 | 9.0 - 11.0 | 65.1 - 79.6 | |
| Upper arm mounting bolt | 137.2 - 156.9 | 14.0 - 16.0 | 101.2 - 115.7 | |
| Lower arm mounting bolt | 137.2 - 156.9 | 14.0 - 16.0 | 101.2 - 115.7 | |
| Asist arm mounting bolt | 137.2 - 156.9 | 14.0 - 16.0 | 101.2 - 115.7 | |
| Trailing arm mounting bolt | 137.2 - 156.9 | 14.0 - 16.0 | 101.2 - 115.7 | |
Lubricants
| Item | Lubricants | Quantity | |
| 1.6 GDI KAPPA | BJ(LH) | RBA | 100 ~ 110g |
| VTJ(LH) | CW-13TJ | 145 ~ 155g | |
| BJ(RH) | RBA | 100 ~ 110g | |
| VTJ(RH) | CW-13TJ | 145 ~ 155g | |
Was this page helpful?