Brake System
Specifications
In this manual: Brake System
~3min read
Specifications
| Item | Specification | |
| Front disc brake | Type | Ventilated disc |
| Disc O.D. | O 280 mm (12.02 in) | |
| Disc thickness | 22 mm (0.86 in) | |
| Caliper piston | Single | |
| Cylinder I.D. | O 57.2 mm (2.25 in) | |
| Rear disc brake | Type | Solid disc |
| Disc O.D. | O 262 mm (10.31 in) | |
| Disc thickness | 10 mm (0.39 in) | |
| Caliper piston | Single | |
| Cylinder I.D. | O 33.96 mm (1.33 in) | |
| Parking brake | Type | BIR (Ball-in-Ramp) |
| Actuation | Lever | |
Specification (ESC)
| Part | Item | Standard value | Remark |
| Integrated Brake Actuation Unit(IBAU) | System | 4 Channel 4 Sensor (Solenoid) | Total control (ABS, EBD, TCS, ESC) |
| Type | Valve relay integrated type | ||
| Operating Voltage | 10 - 15 V | ||
| Operating Temperature | -40 - 120 °C | ||
| Active Wheel speed sensor | Supply voltage | DC 4.5 - 20 V | ? |
| Output current low | 5.9 - 8.4 mA | ? | |
| Output current high | 11.8 - 16.8 mA | ? | |
| Output range | 1 - 2500 Hz | ? | |
| Tone wheel | Front: 48 teeth, Rear: 47 teeth | ? | |
| Air gap | 0.4 - 1.0 mm | ? | |
| Pressure Source Unit (PSU) | System | 3 piston pump/ high pressure accumulator system | ? |
| Operating Voltage | 10 - 15 V | ? | |
| Operating Temperature | -40 - 120 °C | ? |
Service Standard
| Items | Standard value |
| Brake pedal Full stroke | 136.0 mm (5.35 in) |
| Brake pedal height | 177.2 mm (6.97 in.) |
| Stop lamp switch clearance | 1.0 - 2.0 mm (0.04 - 0.08 in) |
| Brake pedal free play | 2.0 - 4.0 mm (0.07 - 0.15 in) |
| Front brake disc thickness | 22.0 mm (0.8661 in) |
| Front brake disc service limit | 20.0 mm (0.7874 in) |
| Front brake disc pad thickness | 17.0 mm (0.6693 in) |
| Front brake disc service limit | 9.0 mm (0.3543 in) |
| Rear brake disc thickness | 10 mm (0.39 in) |
| Rear brake disc service limit | 8.4 mm (0.33 in) |
| Rear brake disc pad thickness | 15.0 mm (0.5906 in) |
| Rear brake disc service limit | 8.0 mm (0.31 in) |
Tightening Torques
| Items | N·m | kgf·m | lb·ft | |
| Air bleeding screw | 6.9 - 12.7 | 0.7 - 1.3 | 5.1 - 9.4 | |
| Front caliper guide rod bolts | 21.6 - 31.4 | 2.2 - 3.2 | 15.9 - 23.1 | |
| Rear caliper guide rod bolts | 21.6 - 31.4 | 2.2 - 3.2 | 15.9 - 23.1 | |
| Front caliper assembly to knuckle | 98.1 - 117.7 | 10.0 -12.0 | 72.3 - 86.8 | |
| Rear caliper assembly to knuckle | 63.7 - 73.5 | 6.5 - 7.5 | 47.0 - 54.2 | |
| Brake hose to caliper | 24.5 - 29.4 | 2.5 - 3.0 | 18.1 - 21.7 | |
| Brake pedal member bracket bolts | 16.7 - 25.5 | 1.7 - 2.6 | 12.3 - 18.8 | |
| Brake pedal mounting nut | 16.7 - 25.5 | 1.7 - 2.6 | 12.3 - 18.8 | |
| Front wheel speed sensor bolt | 7.8 - 11.8 | 0.8 - 1.2 | 5.8 - 8.7 | |
| IBAU bracket mounting bolts | 10.8 - 12.7 | 1.1 - 1.3 | 8.0 - 9.4 | |
| IBAU Brake Tube Flare nuts | 12.7 - 16.7 | 1.3 - 1.7 | 9.4 - 12.3 | |
| PSU Bracket mounting bolts | 19.6 - 29.4 | 2.0 - 3.0 | 14.5 - 21.7 | |
Lubricants
| Items | Recommended | Quantity |
| Brake fluid | DOT 3 or DOT 4 | As required |
| Brake pedal bushing and bolt | Chassis grease | As required |
| Parking brake shoe and backing plate contacting surface | Heat resistance grease | As required |
Was this page helpful?