Mirrors

Auto retractable door mirror circuit

In this manual: Mirrors
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~3min read

Component Function Check

1.CHECK FUNCTION 1. Turn the door mirror open/close switch to “AUTO”. 2. Turn ignition switch ON. 3. Select “INTELLIGENT KEY” of “BCM” using CONSULT-III. 4. Select “RETRACTABLE MIRROR” in “ACTIVE TEST” mode.

5. Touch “On” check that it works normally.

Is the inspection result normal? YES >> INSPECTION END

NO >> Refer to MIR-30, "Diagnosis Procedure"

Diagnosis Procedure

1.CHECK DOOR MIRROR OPEN RELAY AND DOOR MIRROR CLOSE RELAY POWER SUPPLY 1. Turn ignition switch OFF. 2. Disconnect door mirror open relay and door mirror close relay connector.

3. Check voltage between door mirror open relay and door mirror close relay harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.DETECT MALFUNCTIONING PART

Check the following.

• 10 A fuse (#7)
• Harness for open or short between door mirror remote control switch harness connector and battery terminal.

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace the malfunctioning parts.

3.CHECK BCM INPUT SIGNAL CIRCUIT 1. Disconnect BCM connector.

2. Check continuity between door mirror open relay and door mirror close relay harness connector and BCM harness connector

3. Check continuity between BCM harness connector and ground.

3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace harness or connector.

4.CHECK OPEN/CLOSE MOTOR GROUND CIRCUIT 1. Disconnect door mirror remote control switch connector.

2. Check continuity between door mirror remote control switch harness connector and door mirror open relay harness connector.

3. Check continuity between door mirror remote control switch harness

3. Check continuity between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace harness.

5.CHECK DOOR MIRROR OPEN RELAY

Check door mirror open relay.

Refer to MIR-32, "Component Inspection (Door Mirror Open Relay)" Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace harness or connector.

6.CHECK DOOR MIRROR CLOSE RELAY

Check door mirror close relay.

Refer to MIR-32, "Component Inspection (Door Mirror Close Relay)" Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace harness or connector.

7.CHECK BCM FUNCTION 1. Turn the door mirror open/close switch to AUTO. 2. Connect door mirror remote control switch connector, door mirror open relay, door mirror close relay and BCM connector. 3. Turn ignition switch ON. 4. Select “INTELLIGENT KEY” of “BCM” using CONSULT-III. 5. Select “RETRACTABLE MIRROR” in “ACTIVE TEST” mode.

6. Touch “On” and check voltage between BCM harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 8.

NO >> Replace BCM. Refer to BCS-93, "Removal and Installation".

8.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident"

>> INSPECTION END

Component Inspection (Door Mirror Open Relay)

1.CHECK DOOR MIRROR OPEN RELAY 1. Turn ignition switch OFF. 2. Remove door mirror open relay.

3. Check the continuity between door mirror open relay terminals under the following conditions.


Is the inspection result normal?

Is the inspection result normal? YES >> INSPECTION END.

NO >> Replace door mirror open relay.

Component Inspection (Door Mirror Close Relay)

1.CHECK DOOR MIRROR OPEN/CLOSE RELAY 1. Turn ignition switch OFF. 2. Remove door mirror close relay.

3. Check the continuity between door mirror close relay terminals under the following conditions.


Is the inspection result normal?

Is the inspection result normal? YES >> INSPECTION END.

NO >> Replace door mirror close relay.