Front Axle HR16DE

Front drive shaft boot

In this manual: Front Axle HR16DE
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~7min read
060120180240300185136N·mlb·ft
Tightening torque found on this page

Exploded View

LEFT SIDE

1. Circular clip

1. Circular clip
2. Dust shield
3. Housing assembly
4. Boot band
5. Boot
6. Damper band
7. Dynamic damper
8. Circular clip
9. Joint sub-assembly

: Fill NISSAN Genuine grease or: Wheel side
equivalent.: Fill NISSAN Genuine grease or
equivalent.

disassembly.: Always replace after every
disassembly.

RIGHT SIDE

1. Joint sub-assembly

1. Joint sub-assembly 2. Circular clip
3. Boot band
4. Boot
5. Band
6. Dynamic damper
7. Housing assembly
8. Dust shield

: Fill NISSAN Genuine grease or: Wheel side
equivalent.: Fill NISSAN Genuine grease or
equivalent.

disassembly.: Always replace after every
disassembly.

Wheel side : Removal and Installation

REMOVAL

1. Remove tires. Refer to WT-7, "Removal and Installation". 2. Remove wheel sensor and sensor harness. Refer to BRC-84, "FRONT WHEEL SENSOR : Exploded View" (Without ESP) or BRC-224, "FRONT WHEEL SENSOR : Exploded View" (With ESP). 3. Remove lock plate from strut assembly. Refer to FSU-10, "Removal and Installation".

4. Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to BR-57, "BRAKE CALIPER ASSEMBLY : Removal and Installation" (LHD) or BR-123, "BRAKE CALIPER ASSEMBLY : Removal and Installation" (RHD).

CAUTION:
Never depress brake pedal while brake caliper is removed.
5. Remove disc rotor. Refer to FAX-43, "Removal and Installation". 6. Remove cotter pin, and then loosen wheel hub lock nut. Refer to FAX-43, "Removal and Installation".

7. Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub assembly from drive shaft.

NOTE

:
Use suitable puller, if wheel hub assembly and drive shaft cannot be separated even after performing the above procedure.

8. Remove wheel hub lock nut. Refer to FAX-43, "Removal and Installation". 9. Remove strut assembly from steering knuckle. Refer to FAX-43, "Removal and Installation".

10. Remove drive shaft from wheel hub assembly.

CAUTION:

CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.

• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other parts.

11. Remove boot bands, and then remove boot from joint sub-assembly.

12. Screw drive shaft puller (A) (commercial service tool) into joint sub-assembly screw part to a length of 30 mm (1.18 in) or more.

Support drive shaft with one hand and pull out joint sub-assembly from shaft.

CAUTION:
• Align drive shaft puller and drive shaft and remove them by pulling firmly and uniformly.

• If joint sub-assembly cannot be pulled out, try after removing drive shaft from vehicle. Refer to FAX-54, "WHEEL SIDE : Disassembly and Assembly"

.

13. Remove circular clip (1) from shaft.

13. Remove circular clip (1) from shaft.

14. Remove boot from shaft.

INSTALLATION

INSTALLATION

1. Clean the old grease on joint sub-assembly with paper waste.

2. Fill serration slot joint sub-assembly (1) with NISSAN genuine grease or equivalent until the serration slot and ball groove become full to the brim.

CAUTION:
After applying grease, use a paper waste to wipe off old grease that has oozed out.

3. Install boot and boot bands to shaft.

CAUTION:
• Wrap serration on shaft with tape to protect the boot from damage.

• Never reuse boot and boot band

.

4. Remove the tape wrapped around the serration on shaft.

5. Position the circular clip (1) on groove at the shaft edge.

5. Position the circular clip (1) on groove at the shaft edge.

NOTE:

Drive joint inserter is recommended when installing circular clip.

6. Align both center axles of the shaft edge and joint sub-assembly.

Then assemble shaft with joint sub-assembly holding circular clip.

7. Install joint sub-assembly (1) to shaft using plastic hammer.

7. Install joint sub-assembly (1) to shaft using plastic hammer.

CAUTION:
• Check circular clip is properly positioned on groove of the joint sub-assembly.

• Confirm that joint sub-assembly is correctly engaged while rotating drive shaft.

8. Apply the specified amount of grease into the boot inside from large diameter side of boot.

Grease amount : Refer to FAX-60, "Drive Shaft".

9. Install the boot securely into grooves (indicated by “*” marks)

9. Install the boot securely into grooves (indicated by “*” marks) shown in the figure.

CAUTION:
If grease adheres to the boot mounting surface (indicated by “*” marks) on the shaft or joint sub-assembly, boot may be removed. Remove all grease from the boot mounting surface.

10. To prevent the deformation of the boot, adjust the boot installation length (L) to the specified value shown below by inserting the suitable tool into inside of the boot from the large diameter side of the boot and discharging the inside air.

L : Refer to FAX-60, "Drive Shaft".

CAUTION:

CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.

• Be careful not to touch the inside of the boot with a tip of tool.

11. Secure the large and small ends of the boot with boot bands using the boot band crimping tool (A) (SST: KV40107300).

CAUTION:
• Never reuse boot band.
• Secure boot band so that dimension (A) meets the specification

• Secure boot band so that dimension (A) meets the specification as shown in the figure.

A : 5.0 mm (0.197 in) or less.

12. Check that displacement does not occur when boot is rotated with the

12. Check that displacement does not occur when boot is rotated with the joint sub-assembly and shaft fixed.

CAUTION:
• Reinstall them using boot bands when boot installation positions become incorrect.

• Never reuse boot band.

13. Clean the matching surface of wheel hub lock nut and wheel hub assembly.

CAUTION:
Never apply lubricating oil to these matching surface.

14. Clean the matching surface of drive shaft, wheel hub assembly.

And then apply paste [service parts (440037S000)] to surface (A) of joint sub-assembly of drive shaft.

CAUTION:
Apply paste to cover entire flat surface of joint sub-assembly of drive shaft.

Amount paste : 1.0 – 3.0 g (0.04 – 0.10 oz)

15. Insert drive shaft to wheel hub assembly, and then temporarily

15. Insert drive shaft to wheel hub assembly, and then temporarily tighten wheel hub lock nut.

CAUTION:
Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool. 16. Install strut assembly to steering knuckle. Refer to FSU-10, "Removal and Installation". 17. Install disc rotor. Refer to FAX-43, "Removal and Installation". 18. Install caliper assembly to steering knuckle. Refer to BR-57, "BRAKE CALIPER ASSEMBLY : Removal and Installation" (LHD) or BR-123, "BRAKE CALIPER ASSEMBLY : Removal and Installation" (RHD). 19. Install lock plate to strut assembly. Refer to FSU-10, "Removal and Installation". 20. Install wheel sensor and sensor harness. Refer to BRC-84, "FRONT WHEEL SENSOR : Exploded View" (Without ESP) or BRC-224, "FRONT WHEEL SENSOR : Exploded View" (With ESP).

21. Use the following torque range for tightening the wheel hub lock nut.

kg-m, 133 – 136 ft-lb): 180 – 185 N·m (18.4 – 18.8
kg-m, 133 – 136 ft-lb)

CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel hub lock nut. • Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.

• Never reuse wheel hub lock nut.

NOTE

:
Wheel hub lock nut tightening torque does not over torque for avoiding axle noise, and does not less than torque for avoiding looseness.

22. When installing a cotter pin (1) and adjusting cap (2), securely bend the basal portion to prevent rattles.

CAUTION:
Never reuse cotter pin.
23. Install tires. Refer to WT-7, "Removal and Installation".

24. Perform inspection after installation. Refer to FAX-51, "Inspection".

Transaxle side : Removal and Installation

Transaxle side : Removal and Installation

Remove boot after drive shaft is removed from the vehicle.

• For drive shaft removal and installation, refer to FAX-53, "Removal and Installation".

• For drive shaft disassembly and assembly, refer to FAX-56, "TRANSAXLE SIDE : Disassembly and Assembly".

Inspection

INSPECTION AFTER INSTALLATION

1. Check wheel sensor harness for proper connection. Refer to BRC-84, "FRONT WHEEL SENSOR : Exploded View" (Without ESP) or BRC-224, "FRONT WHEEL SENSOR : Exploded View" (With ESP).

2. Check the wheel alignment. Refer to FSU-7, "Inspection".