Door & Lock type 3

Rear door lock

In this manual: Door & Lock type 3
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~3min read

Exploded View

1. Outside handle assembly

1. Outside handle assembly 2. Inside handle
3. TORX bolt
4. Door lock assembly
5. Rear door sealing screen

: Pawl: Clip
: Vehicle front: Pawl
: Do not reuse: Vehicle front
: N·m (kg-m, in-lb): Do not reuse
: Body grease: N·m (kg-m, in-lb)
Door lock: Body grease


Door lock

DOOR LOCK : Removal and Installation

REMOVAL

1. Remove rear door glass and rear door lower sash (rear). Refer to GW-21, "Removal and Installation". 2. Remove inside handle. Refer to DLK-478, "INSIDE HANDLE : Removal and Installation". 3. Remove outside handle. Refer to DLK-478, "OUTSIDE HANDLE : Removal and Installation". 4. Remove door lock assembly TORX bolts.

5. Disconnect door lock actuator connector, and then remove door lock assembly.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed. • Check door open/close, lock/unlock operation after installation.

• Check door lock assembly for poor lubrication. Apply body grease to door lock if necessary.

: Grease up point


Inside handle

Inside handle

INSIDE HANDLE : Removal and Installation

REMOVAL

1. Remove rear door finisher. Refer to INT-16, "Removal and Installation".

2. Remove upper side of sealing screen.

NOTE

:
Cut the butyl tape so that some parts of the butyl tape do not remain on the sealing screen, if the sealing screen is reused.

3. Remove inside handle mounting bolt (A).

4. Disengage inside handle (1) from door panel (2) while sliding inside handle toward vehicle rear, and then separate inside handle.

: Vehicle front


5. Disengage inside handle cable (2), and then remove inside handle

5. Disengage inside handle cable (2), and then remove inside handle (1).

INSTALLATION

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:
Check door open/close, lock/unlock operation after installation.

Outside handle

OUTSIDE HANDLE : Removal and Installation

REMOVAL

1. Remove rear door finisher and rear door corner cover inner. Refer to INT-16, "Removal and Installation". 2. Remove rear door sealing screen. 3. Rotate stopper (1) upward.

4. Disengage outside handle cable (2), and then remove outside handle cable from outside handle assembly (3).

5. Remove outside handle assembly mounting bolts (A).

5. Remove outside handle assembly mounting bolts (A).

6. Disengage mounting clips using a remover tool (A), and then

6. Disengage mounting clips using a remover tool (A), and then remove outside handle assembly.

CAUTION:
Apply protective tape (B) on the door panel to protect the painted surface from damage.

: Clip


INSTALLATION

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Never reuse rear door sealing screen. Always replace it with a new one when it is removed. When installing rear door sealing screen, install it according to the following procedure. - Put lower portion of rear door sealing screen (1) into inside of door panel (2). - Perform positioning according to the following procedure, and then install rear door sealing screen. • Align upper portion of rear door sealing screen to hole (A) of door panel as shown in the figure.

• Align hole of rear door sealing screen to edge (B) of door panel as shown in the figure.

• Be careful to position outside handle cable normally when installing it.

• Be careful to position outside handle cable normally when installing it. For details, refer to DLK-477, "Exploded View".

• Check door open/close, lock/unlock operation after installation.