Charging System

Removal and installation

In this manual: Charging System
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~7min read
ALTERNATOR HR16DE HR16DE : Exploded View

REMOVAL

1. Alternator bracket mounting bolt

1. Alternator bracket mounting bolt 2. Alternator bracket
3. Alternator mounting bolt 4. Alternator
5. “B” terminal harness 6. “B” terminal nut
7. Alternator connector

DISASSEMBLY: N·m (kg-m, ft-lb)


DISASSEMBLY

Type: A002TJ1291ZE

1. Rear bearing

1. Rear bearing
2. Rotor assembly
3. Retainer
4. Front bearing
5. Front bracket assembly 6. Pulley
7. Pulley nut
8. Stator assembly
9. IC voltage regulator assembly 10. Diode assembly
11. Rear bracket assembly 12. Terminal set

: N·m (kg-m, in-lb):

Do not reuse
: N·m (kg-m, ft-lb): N·m (kg-m, in-lb)
HR16DE : Removal and Installation: N·m (kg-m, ft-lb)


HR16DE : Removal and Installation

REMOVAL

1. Disconnect the battery cable from the negative terminal. Refer to PG-124, "Removal and Installation". 2. Remove radiator reservoir tank. Refer to CO-17, "Exploded View". 3. Remove drive belt. Refer to EM-155, "Removal and Installation". 4. Disconnect alternator connector. 5. Remove “B” terminal nut and disconnect “B” terminal harness. 6. Remove alternator mounting bolts.

7. Remove alternator upward from the vehicle.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:
• Temporarily tighten the alternator bolts in order from the lower to the upper, and then tighten them in order from the upper to the lower. • For the alternator, the front side (pulley side) surface is the reference surface. Fit the reference surface to the alternator mounting part, and then tighten the bolts. • Be careful to tighten “B” terminal nut carefully.

• Install alternator, and check tension of belt. Refer to EM-154, "Checking".

NOTE:

Tighten mounting bolts according to the following procedures for installing alternator bracket.

1. Temporarily tighten mounting bolt (1). 2. Temporarily tighten mounting bolt (2).

3. Tighten mounting bolts in numerical order as shown in the figure.

HR16DE : Disassembly and Assembly

HR16DE : Disassembly and Assembly

DISASSEMBLY

Rear Cover
NOTE

:
Rear cover may be hard to remove because a ring is used to lock outer race of rear bearing. To facilitate removal of rear cover, heat only the bearing box section until the temperature increases to approximately 30 °C with a soldering iron (200W capacity).

CAUTION:
Never use a heat gun, as if can damage diode assembly.
ASSEMBLY

ASSEMBLY

Rear Bearing CAUTION:
• Never reuse rear bearing. Replace with a new one.

• Never lubricate rear bearing outer race.

Rear Cover Installation 1. Fit brush assembly, diode assembly, regulator assembly and stato

2. Push brushes up with fingers and install them to rotor.

2. Push brushes up with fingers and install them to rotor.

NOTE

:
Take care not damage slip ring sliding surface.

HR16DE : Inspection

HR16DE : Inspection

INSPECTION

Rotor Check
1. Resistance test

Resistance : Refer to SDS CHG-35, "Alternator".

• Replace the rotor if the measurement value is outside of the specified range.

2. Insulator test
• Replace the rotor if continuity exists.

3. Check slip ring for wear.

Slip ring minimum outer diameter : Refer to SDS CHG-35, "Alternator".

• Replace the rotor if the measurement value is outside of the specified range.

Brush Check

Brush Check
1. Check smooth movement of brush.

• Check brush holder and clean if it is not smooth.

2. Check brush for wear.

• Replace brush if it is worn down to the limit line.

Stator Check

Stator Check
1. Continuity test
• Replace the stator if continuity does not exist.

2. Ground test

2. Ground test
• Replace the stator if continuity exists.

MR16DDT

MR16DDT MR16DDT : Exploded View

REMOVAL

1. Alternator connector

1. Alternator connector 2. Alternator mounting bolt (upper) 3. Alternator mounting bolt (lower) 4. Alternator
5. “B” terminal harness 6. “B” terminal nut

DISASSEMBLY: N·m (kg-m, ft-lb)


DISASSEMBLY

Type: A002TJ1381

1. Rear bearing

1. Rear bearing
2. Rotor assembly
3. Retainer
4. Front bearing
5. Front bracket assembly 6. Pulley
7. Pulley cap
8. Stator assembly
9. IC voltage regulator assembly 10. Diode assembly
11. Rear bracket assembly 12. Terminal set

: N·m (kg-m, in-lb): Do not reuse
: N·m (kg-m, ft-lb): N·m (kg-m, in-lb)
MR16DDT : Removal and Installation: N·m (kg-m, ft-lb)


MR16DDT : Removal and Installation

REMOVAL

1. Disconnect the battery cable from the negative terminal. Refer to PG-124, "Removal and Installation". 2. Remove charge air cooler. Refer to EM-31, "Removal and Installation". 3. Remove drive belt. Refer to EM-20, "Removal and Installation". 4. Disconnect alternator connector. 5. Remove “B” terminal nut and disconnect “B” terminal harness. 6. Remove alternator mounting bolt (upper).

7. Completely loosen alternator mounting bolt (lower), and pull it out until the bolt head is in contact with the side member. And then, remove the alternator by pulling it forward.

NOTE

:
The alternator can be removed together with the bolts by pulling it forward and using the thermostat housing bolt hole cutout.

8. Remove alternator forward from the vehicle.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:
• Temporarily tighten the alternator bolts in order from the lower to the upper, and then tighten them in order from the upper to the lower

. • For the alternator, the front side (pulley side) surface is the reference surface. Fit the reference surface to the alternator mounting part, and then tighten the bolts.

• Be careful to tighten “B” terminal nut carefully.

• Install alternator, and check tension of belt. Refer to EM-20, "Checking".

• For this model, the power generation voltage variable control system that controls the power generation voltage of the alternator has been adopted. Therefore, the power generation voltage variable control system operation inspection should be performed after replacing the alternator, and then make sure that the system operates normally. Refer to CHG-18, "Inspection Procedure". MR16DDT : Disassembly and Assembly

DISASSEMBLY

Rear Cover NOTE

:
Rear cover may be hard to remove because a ring is used to lock outer race of rear bearing. To facilitate removal of rear cover, heat only the bearing box section until the temperature increases to approximately 30 °C with a soldering iron (200W capacity).

CAUTION:
Never use a heat gun, as if can damage diode assembly.
Front Cover

Front Cover
1. Set rotor to the vise.

CAUTION:
• Be careful not to damage the rotor.

• Use copper plate or thick cloth for rotor in the vise.

2. Remove pulley cap, using suitable tool.

3. Remove alternator pulley, using alternator pulley adaptor [SST].

3. Remove alternator pulley, using alternator pulley adaptor [SST].

ASSEMBLY

ASSEMBLY

Rear Bearing
CAUTION:
• Never reuse rear bearing. Replace with a new one.

• Never lubricate rear bearing outer race.

Rear Cover Installation

1. Fit brush assembly, diode assembly, regulator assembly and stator assembly.

2. Push brushed up with fingers and install them to rotor.

2. Push brushed up with fingers and install them to rotor.

NOTE

:
Take care not damage slip ring sliding surface.

MR16DDT : Inspection

MR16DDT : Inspection

INSPECTION AFTER DISASSEMBLY

Rotor Check
1. Resistance test

Resistance : Refer to SDS CHG-35, "Alternator".

• Replace the rotor if the measurement value is outside of the specified range.

2. Insulator test
• Replace the rotor if continuity exists.

3. Check slip ring for wear.

Slip ring minimum outer diameter : Refer to SDS CHG-35, "Alternator".

• Replace the rotor if the measurement value is outside of the specified range.

Brush Check

Brush Check
1. Check smooth movement of brush.

• Check brush holder and clean if it is not smooth.

2. Check brush for wear.

• Replace brush if it is worn down to the limit line.

Stator Check

Stator Check
1. Continuity test
• Replace the stator if continuity does not exist.

2. Ground test

2. Ground test
• Replace the stator if continuity exists.

Service data and specifications (SDS)