Driver Seat Control Unit
| Monitor Item | Condition | Value/Status | |
|---|---|---|---|
| STARTER SW | Ignition position | Cranking | ON |
| Other than above | OFF | ||
| SET SW | Set switch | Push | ON |
| Release | OFF | ||
| MEMORY SW 1 | Memory switch 1 | Push | ON |
| Release | OFF | ||
| MEMORY SW 2 | Memory switch 2 | Push | ON |
| Release | OFF | ||
| DETENT SW | CVT selector lever | P position | OFF |
| Other than above | ON | ||
| STEERING STATUS | Power supply position of BCM | LOCK | LOCK |
| Other than the above | UNLOCK | ||
| SLIDE SW–FR | Sliding switch (forward) | Operate | ON |
| Release | OFF | ||
| SLIDE SW–RR | Sliding switch (backward) | Operate | ON |
| Release | OFF | ||
| RECLN SW–FR | Reclining switch (forward) | Operate | ON |
| Release | OFF | ||
| RECLN SW–RR | Reclining switch (backward) | Operate | ON |
| Release | OFF | ||
| LIFT FR SW–UP | Lifting switch front (upward) | Operate | ON |
| Release | OFF | ||
| LIFT FR SW–DN | Lifting switch front (downward) | Operate | ON |
| Release | OFF | ||
| LIFT RR SW–UP | Lifting switch rear (upward) | Operate | ON |
| Release | OFF | ||
| LIFT RR SW–DN | Lifting switch rear (downward) | Operate | ON |
| Release | OFF | ||
| TILT SW-UP | Tilt switch | Upward | ON |
| Other than above | OFF | ||
| TILT SW-DOWN | Tilt switch | Downward | ON |
| Other than above | OFF | ||
| TELESCO SW-FR | Telescopic switch | Forward | ON |
| Other than above | OFF | ||
| TELESCO SW-RR | Telescopic switch | Backward | ON |
| Other than above | OFF | ||
| MIR CON SW–UP | Mirror switch | Up | ON |
| Other than above | OFF | ||
| MIR CON SW–DN | Mirror switch | Down | ON |
| Other than above | OFF | ||
| MIR CON SW–RH | Mirror switch | Right | ON |
| Other than above | OFF | ||
| MIR CON SW–LH | Mirror switch | Left | ON |
| Other than above | OFF | ||
| MIR CHNG SW–R | Select switch | Right | ON |
| Other than above | OFF | ||
| MIR CHNG SW–L | Select switch | Left | ON |
| Other than above | OFF | ||
| TILT PULSE | Tilt position | Upward | The numeral value decreases * |
| Downward | The numeral value increases * | ||
| Other than above | No change to numeral value* | ||
| TELESCO PULSE | Telescopic position | Forward | The numeral value decreases * |
| Backward | The numeral value increases * | ||
| Other than above | No change to numeral value* | ||
| MIR/SEN RH U–D | Door mirror RH | Change between 3.4 (close to peak) 0.6 (close to valley) |
|
| MIR/SEN RH R–L | Door mirror RH | Change between 3.4 (close to left edge) 0.6 (close to right edge) |
|
| MIR/SEN LH U–D | Door mirror LH | Change between 3.4 (close to peak) 0.6 (close to valley) |
|
| MIR/SEN LH R–L | Door mirror LH | Change between 0.6 (close to left edge) 3.4 (close to right edge) |
|
| SLIDE PULSE | Seat sliding | Forward | The numeral value decreases * |
| Backward | The numeral value increases* | ||
| Other than above | No change to numeral value* | ||
| RECLN PULSE | Seat reclining | Forward | The numeral value decreases* |
| Backward | The numeral value increases * | ||
| Other than above | No change to numeral value* | ||
| LIFT FR PULSE | Seat lifter (front) | Upward | The numeral value decreases * |
| Downward | The numeral value increases * | ||
| Other than above | No change to numeral value* | ||
| LIFT RR PULSE | Seat lifter (rear) | Upward | The numeral value decreases * |
| Downward | The numeral value increases * | ||
| Other than above | No change to numeral value* | ||
| Nissan Murano Vehicle SPEED | The condition of vehicle speed is displayed | km/h | |
| P RANG SW CAN | CVT selector lever | P position | ON |
| Other than above | OFF | ||
| R RANGE (CAN) | CVT selector lever | R position | ON |
| Other than above | OFF | ||
| DOOR SW-FL | Driver door | Open | OPEN |
| Close | CLOSED | ||
| DOOR SW-FR | Passenger door | Open | OPEN |
| Close | CLOSED | ||
| IGN ON SW | Ignition switch | ON position | ON |
| Other than above | OFF | ||
| ACC ON SW | Ignition switch | ACC or ON position | ON |
| Other than above | OFF | ||
| KYLS DR UNLK | Intelligent Key or driver side door request switch | ON | ON |
| OFF | OFF | ||
| KEYLESS ID | UNLOCK button of Intelligent Key is pressed | 1, 2, 3, 4 or 5 | |
| VHCL SPEED (ABS) | CAN signal from ABS | Received | ON |
| Not received | OFF | ||
| HANDLE | Driving position | LHD | |
| RHD | |||
| TRANSMISSION | Transmission type | CVT | |
| KEY NUMBER | KEY 1 | ||
| KEY 1 | NO REG | ||
| KEY 2 | NO REG | ||
| KEY 3 | NO REG | ||
| KEY 4 | NO REG | ||
*: The value at the position attained when the battery is connected is regarded as 32768.
TERMINAL LAYOUT

PHYSICAL VALUES
Terminal No. (wire color) | Description | Condition | Voltage (Approx.) | |||
|---|---|---|---|---|---|---|
| + | - | Signal name | Input/Output | |||
5 (W) |
Ground | Sensor power supply | Output | — | Battery voltage | |
6 (R) |
Ground | Lifting switch (rear) down signal | Input | Seat lifting switch (rear) |
Operate (down) |
0V |
| Release | Battery voltage | |||||
7 (Y) |
Ground | Lifting switch (front) down signal | Input | Seat lifting switch (front) | Operate (down) |
0V |
| Release | Battery voltage | |||||
8 (BR) |
Ground | Reclining switch backward signal | Input | Reclining switch | Operate (backward) |
0V |
| Release | Battery voltage | |||||
9 (SB) |
Ground | Sliding switch backward signal | Input | Sliding switch | Operate (backward) |
0V |
| Release | Battery voltage | |||||
10 (G) |
Ground | Memory indicator 2 signal | Output | Memory indicator 2 | Illuminate | 1V |
| Other than above | Battery voltage | |||||
11 (GR) |
Ground | Memory switch 2 signal | Input | Memory switch 2 | Press | 0V |
| Other than above | 5V | |||||
12 (W) |
Ground | Telescopic sensor signal | Input | Telescopic | Operate | ![]() |
| Other than above | 0V or 5V | |||||
13 (G) |
Ground | Reclining sensor signal | Input | Seat reclining | Operate | ![]() |
| Stop | 0V or 5V | |||||
15 (SB) |
Ground | UART communication (TX/RX) | Input | Ignition switch ON | ![]() |
|
16 (P) |
— | CAN-High | — | — | — | |
21 (L) |
Ground | Set switch signal | Input | Set switch | Press | 0V |
| Other than above | 5V | |||||
22 (V) |
Ground | Lifting switch (rear) up signal | Input | Lifting switch (rear) | Operate (up) |
0V |
| Release | Battery voltage | |||||
23 (G) |
Ground | Lifting switch (front) up signal | Input | Lifting switch (front) | Operate (up) |
0V |
| Release | Battery voltage | |||||
24 (P) |
Ground | Reclining switch forward signal | Input | Reclining switch | Operate (forward) |
0V |
| Release | Battery voltage | |||||
25 (L) |
Ground | Sliding switch forward signal | Input | Sliding switch | Operate (forward) |
0V |
| Release | Battery voltage | |||||
26 (Y) |
Ground | Memory indicator 1 signal | Output | Memory indicator 1 | Illuminate | 1V |
| Other than above | Battery voltage | |||||
27 (V) |
Ground | Memory switch 1 signal | Input | Memory switch 1 | Press | 0V |
| Other than above | 5V | |||||
28 (BR) |
Ground | Tilt sensor signal | Input | Tilt | Operate | ![]() |
| Other than above | 0V or 5V | |||||
29 (R) |
Ground | Lifting sensor (rear) signal | Input | Seat lifting (rear) | Operate | ![]() |
| Stop | 0V or 5V | |||||
30 (Y) |
Ground | Lifting sensor (front) signal | Input | Seat lifting (front) | Operate | ![]() |
| Stop | 0V or 5V | |||||
31 (LG) |
Ground | Sliding sensor signal | Input | Seat sliding | Operate | ![]() |
| Stop | 0V or 5V | |||||
32 (W) |
— | CAN-Low | — | — | — | |
34 (SB) |
Ground | Lifting motor LH (front) up signal | Output | Seat lifting (front) | Operate (up) |
Battery voltage |
| Stop | 0V | |||||
35 (V) |
Ground | Reclining motor LH forward signal | Output | Seat reclining | Operate (forward) |
Battery voltage |
| Release | 0V | |||||
36 (W) |
Ground | Sliding motor LH backward signal | Output | Seat sliding | Operate (backward) |
Battery voltage |
| Stop | 0V | |||||
37 (R) |
Ground | Battery power supply | Input | — | Battery voltage | |
39 (B) |
Ground | Ground | — | — | 0V | |
40 (L) |
Ground | Lifting motor LH (rear) down signal | Output | Seat lifting (rear) | Operate (down) |
Battery voltage |
| Stop | 0V | |||||
41 (Y) |
Ground | Lifting motor LH (rear) up signal | Output | Seat lifting (rear) | Operate (up) |
Battery voltage |
| Stop | 0V | |||||
42 (GR) |
Ground | Lifting motor LH (front) down signal | Output | Seat lifting (front) | Operate (down) |
Battery voltage |
| Stop | 0 V | |||||
43 (BR) |
Ground | Reclining motor LH backward signal | Output | Seat reclining | Operate (backward) |
Battery voltage |
| Stop | 0V | |||||
44 (G) |
Ground | Sliding motor LH forward signal | Output | Seat sliding | Operate (forward) |
Battery voltage |
| Release | 0V | |||||
The fail-safe mode may be activated if the following symptoms are observed.
Operating in fail-safe mode | Malfunction Item | Related DTC | Diagnosis |
|---|---|---|---|
| Only manual functions operate normally. | CAN communication | U1000 | DTC Description |
| CONTROL UNIT | U1010 | DTC Description | |
| EEPROM | B2130 | DTC Description | |
| Only manual functions, except door mirror, operate normally. | UART communication | B2128 | DTC Description |
| Only manual functions, except seat sliding, operate normally. | Seat sliding output | B2112 | DTC Description |
| Only manual functions, except seat reclining, operate normally. | Seat reclining output | B2113 | DTC Description |
| Only manual functions, except steering tilt, operate normally. | Steering column tilt output | B2116 | DTC Description |
CONSULT display | Timing*1 | Item | Reference page | |
|---|---|---|---|---|
| Current malfunction | Previous malfunction | |||
CAN COMM CIRCUIT [U1000] |
0 | 1-39 | CAN communication | DTC Description |
CONTROL UNIT(CAN) [U1010] |
0 | 1-39 | Control unit | DTC Description |
SEAT SLIDE [B2112] |
0 | 1-39 | Seat slide motor output | DTC Description |
SEAT RECLINING [B2113] |
0 | 1-39 | Seat reclining motor output | DTC Description |
STEERING TILT [B2116] |
0 | 1-39 | Tilt motor output | DTC Description |
UART COMM [B2128] |
0 | 1-39 | UART communication | DTC Description |
EEPROM [B2130] |
0 | 1-39 | EEPROM | DTC Description |
*1: About timing
0: Current malfunction is present.
1-39: Displayed if any previous malfunction is present when current condition is normal. The numeral value increases by one at each IGN ON to OFF cycle from 1 to 39. The counter remains at 39 even if the number of cycles exceeds it. However, the counter is reset to 1 if any malfunction is detected again, the normal operation is resumed and the ignition switch from OFF to ON.

