Vehicle Exterior

Inspection

~2min read

INSPECTION

PROCEDURE

1. INSPECT OUTER MIRROR SWITCH ASSEMBLY

(a) Check the mirror select and surface adjust switch.

(1) Turn the mirror select and surface adjust switch to the L position.

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):

Tester Connection

Condition

Specified Condition

L11-6 (B) - L11-2 (VL)

L11-7 (E) - L11-11 (M+)

Up

Below 1 Ω

L11-6 (B) - L11-2 (VL)

L11-7 (E) - L11-11 (M+)

Off

10 kΩ or higher

L11-6 (B) - L11-11 (M+)

L11-7 (E) - L11-2 (VL)

Down

Below 1 Ω

L11-6 (B) - L11-11 (M+)

L11-7 (E) - L11-2 (VL)

Off

10 kΩ or higher

L11-6 (B) - L11-4 (HL)

L11-7 (E) - L11-11 (M+)

Left

Below 1 Ω

L11-6 (B) - L11-4 (HL)

L11-7 (E) - L11-11 (M+)

Off

10 kΩ or higher

L11-6 (B) - L11-11 (M+)

L11-7 (E) - L11-4 (HL)

Right

Below 1 Ω

L11-6 (B) - L11-11 (M+)

L11-7 (E) - L11-4 (HL)

Off

10 kΩ or higher

*a

Mirror Select and Surface Adjust Switch

*b

Component without harness connected

(Outer Mirror Switch Assembly)

(3) Turn the mirror select and surface adjust switch to the R position.

(4) Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):

Tester Connection

Condition

Specified Condition

L11-6 (B) - L11-5 (VR)

L11-7 (E) - L11-11 (M+)

Up

Below 1 Ω

L11-6 (B) - L11-5 (VR)

L11-7 (E) - L11-11 (M+)

Off

10 kΩ or higher

L11-6 (B) - L11-11 (M+)

L11-7 (E) - L11-5 (VR)

Down

Below 1 Ω

L11-6 (B) - L11-11 (M+)

L11-7 (E) - L11-5 (VR)

Off

10 kΩ or higher

L11-6 (B) - L11-3 (HR)

L11-7 (E) - L11-11 (M+)

Left

Below 1 Ω

L11-6 (B) - L11-3 (HR)

L11-7 (E) - L11-11 (M+)

Off

10 kΩ or higher

L11-6 (B) - L11-11 (M+)

L11-7 (E) - L11-3 (HR)

Right

Below 1 Ω

L11-6 (B) - L11-11 (M+)

L11-7 (E) - L11-3 (HR)

Off

10 kΩ or higher

If the result is not as specified, replace the outer mirror switch assembly.

(b) Check that the LED illuminates.

(1) Apply auxiliary battery voltage to the terminals of the connector, and check that the LED illuminates.

OK:

Tester Connection

Specified Condition

L11-12 (ILL+) - Auxiliary battery positive (+)

L11-1 (ILL-) - Auxiliary battery negative (-)

LED illuminates

If the result is not as specified, replace the outer mirror switch assembly.

*a

Component without harness connected

(Outer Mirror Switch Assembly)