Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) |
17410 |
- |
- |
|
2 |
AIR FUEL RATIO SENSOR |
89467C |
- |
- |
- |
3 |
TAIL EXHAUST PIPE ASSEMBLY |
17430 |
- |
- |
|
4 |
FRONT FLOOR CENTER BRACE |
57533B |
- |
- |
- |
5 |
INSPECT FOR EXHAUST GAS LEAK |
- |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
PROCEDURE
1. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
*1 |
Exhaust Manifold (TWC: Front Catalyst) |
*2 |
Gasket |
*a |
Wooden Block |
*b |
Plastic Hammer |
(1) Using a vernier caliper, measure the free length of the compression springs.
Standard Length |
43 mm (1.69 in.) |
Minimum Free Length |
41.5 mm (1.63 in.) |
If the free length is less than the minimum, replace the compression spring.
(2) Temporarily install a new gasket to the exhaust manifold (TWC: Front Catalyst).
(3) Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold (TWC: Front Catalyst).
NOTICE:
- Be careful with the installation direction of the gasket.
- Do not reuse the gasket.
- Do not damage the gasket.
- Do not push in the gasket by using the exhaust pipes when connecting them.
*1 |
Exhaust Manifold (TWC: Front Catalyst) |
*2 |
Front Exhaust Pipe Assembly (TWC: Rear Catalyst) |
*3 |
Gasket |
- |
- |
*a |
Space between Flanges: 8.5 mm (0.335 in.) |
- |
- |
(1) Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.
(2) Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.
Torque:
43 N·m {438 kgf·cm, 32 ft·lbf}
(3) After installation, check that the space between the flanges of the exhaust manifold and front exhaust pipe assembly is consistent front-to-rear and left-to-right.
2. INSTALL AIR FUEL RATIO SENSOR
Click here ![]()
3. INSTALL TAIL EXHAUST PIPE ASSEMBLY
*1 |
Front Exhaust Pipe Assembly (TWC: Rear Catalyst) |
*2 |
Gasket |
*a |
Wooden Block |
*b |
Plastic Hammer |
(1) Using a vernier caliper, measure the free length of the compression springs.
Standard Length |
40 mm (1.57 in.) |
Minimum Free Length |
38.5 mm (1.52 in.) |
If the free length is less than the minimum, replace the compression spring.
(2) Temporarily install a new gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).
(3) Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front exhaust pipe assembly (TWC: Rear Catalyst).
NOTICE:
- Be careful with the installation direction of the gasket.
- Do not reuse the gasket.
- Do not damage the gasket.
- Do not push in the gasket by using the exhaust pipes when connecting them.
*1 |
Front Exhaust Pipe Assembly (TWC: Rear Catalyst) |
*2 |
Tail Exhaust Pipe Assembly |
*3 |
Gasket |
- |
- |
*a |
Space between Flanges: 6.5 mm (0.256 in.) |
- |
- |
(1) Connect the tail exhaust pipe assembly to the 3 exhaust pipe supports.
(2) Install the tail exhaust pipe assembly to the front exhaust pipe assembly (TWC: Rear Catalyst) with the 2 compression springs and 2 bolts.
Torque:
43 N·m {438 kgf·cm, 32 ft·lbf}
(3) After installation, check that the space between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.
4. INSTALL FRONT FLOOR CENTER BRACE
Click here ![]()
5. INSPECT FOR EXHAUST GAS LEAK
(1) If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.
HINT:
Perform "Inspection After Repairs" after repairing or replacing the exhaust system.
Click here ![]()
.png)
.png)
.png)
.gif)
.png)