Installation
INSTALLATION
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
INSPECT SPIRAL CABLE SUB-ASSEMBLY |
- |
- |
- |
|
2 |
STEERING SENSOR |
89245B |
- |
- |
|
3 |
PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
- |
- |
- |
|
4 |
SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
- |
- |
- |
|
5 |
UPPER STEERING COLUMN COVER |
45286B |
- |
- |
- |
6 |
LOWER STEERING COLUMN COVER |
45287 |
- |
- |
- |
7 |
SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
- |
- |
- |
|
8 |
STEERING WHEEL ASSEMBLY |
45100 |
- |
- |
- |
9 |
CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
10 |
INSPECT SRS WARNING LIGHT |
- |
- |
- |
|
11 |
INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
*1 |
SPIRAL CABLE SUB-ASSEMBLY |
- |
- |
PROCEDURE
1. INSPECT SPIRAL CABLE SUB-ASSEMBLY
*a |
Check Window |
*b |
Matchmark |
*c |
Top of Flat Cable U-turn |
- |
- |
(1) Check if the spiral cable sub-assembly is centered.
OK:
The connector is at the top.
The matchmarks are aligned.
The top of the flat cable U-turn can be checked from the check window.
*a |
Interlock |
*b |
Check Window |
*c |
Matchmark |
*d |
Top of Flat Cable U-turn |
![]() |
Rotation Direction |
- |
- |
(1) If the spiral cable sub-assembly is not centered, center it.
NOTICE:
Make sure to observe the following precautions, otherwise the spiral cable sub-assembly may be damaged.
- Release the interlock before rotating the spiral cable sub-assembly.
- Do not rotate the spiral cable sub-assembly using the airbag wire harness.
- Do not rotate the spiral cable sub-assembly with excessive force.
- While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.
NOTICE:
Make sure to rotate the spiral cable with sensor sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.
HINT:
The interlock operates at the top and bottom of the connector.
- If the spiral cable with sensor sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.
- While pushing on the interlock, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.
NOTICE:
If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.
HINT:
The interlock operates at the top and bottom of the connector.
- Check that the spiral cable with sensor sub-assembly is center position.
OK:
The connector is at the top.
The matchmarks are aligned.
The colored roller or the top of the flat cable U-turn can be checked from the check window.
NOTICE:
If the spiral cable with sensor sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.
2. INSTALL STEERING SENSOR
![]() |
NOTICE: Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly. |
(a) Align the 2 pins and 2 guides, and engage the 6 claws to install the spiral cable sub-assembly to the steering sensor.
*a |
Lock Pin |
*b |
Guide |
(1) Align the guides to install the steering sensor to the spiral cable sub-assembly.
(2) Engage the claws to install the steering sensor to the spiral cable sub-assembly.
NOTICE:
- Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.
- Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.
- The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.
(3) Remove the lock pin from the steering sensor.
3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
4. INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
![]() |
NOTICE:
|
*A |
w/ Smart Key System |
*B |
w/o Smart Key System |
*a |
Illumination off |
- |
- |
(1) Check that the ignition switch is off.
(2) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
(1) Check that the front wheels are aligned facing straight ahead.
(2) Set the turn signal switch to the neutral position.
NOTICE:
If it is not in the neutral position, the turn signal switch cancel ratchet may snap.
(1) Engage the claw and clip to install the spiral cable with sensor sub-assembly.
(2) Install the wire harness to the spiral cable with sensor sub-assembly.
(3) Connect each connector.
(4) Connect the airbag connector.
NOTICE:
When connecting any airbag connector, take care not to damage the airbag wire harness.
HINT:
Refer to How to Connect or Disconnect Airbag Connector:
Click here ![]()
5. INSTALL UPPER STEERING COLUMN COVER
6. INSTALL LOWER STEERING COLUMN COVER
7. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
![]() |
NOTICE: Do not rotate the spiral cable with sensor sub-assembly with the battery connected and the ignition switch on (IG). |
*A |
w/ Smart Key System |
*B |
w/o Smart Key System |
*a |
Illumination off |
- |
- |
(1) Check that the ignition switch is off.
(2) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
*a |
Check Window |
*b |
Top of Flat Cable U-turn |
(1) Check that the spiral cable with sensor sub-assembly is center position.
OK:
The connector is at the top.
The top of the flat cable U-turn can be checked from the check window.
*a |
Interlock |
*b |
Check Window |
*c |
Top of Flat Cable U-turn |
- |
- |
![]() |
Rotation Direction |
- |
- |
(1) If the spiral cable with sensor sub-assembly is not centered, center it.
NOTICE:
Failure to observe the following precautions may result in damage to the spiral cable with sensor sub-assembly.
- When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock to release the interlock.
- Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.
- Do not forcibly rotate the part.
- While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.
NOTICE:
If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.
HINT:
The interlock operates at the top and bottom of the connector.
- If the spiral cable with sensor sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.
- While pushing on the interlock, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.
NOTICE:
If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.
HINT:
The interlock operates at the top and bottom of the connector.
- Check that the spiral cable with sensor sub-assembly is center position.
OK:
The connector is at the top.
The colored roller or the top of the flat cable U-turn can be checked from the check window.
NOTICE:
If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.
8. INSTALL STEERING WHEEL ASSEMBLY
Click here ![]()
9. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
- for Gasoline Model
Click here
.gif)
- for HEV Model
Click here
.gif)
10. INSPECT SRS WARNING LIGHT
![]() |
Click here |
11. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here ![]()
.png)
.png)
.png)
.png)