Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
REAR BUMPER ASSEMBLY |
- |
- |
- |
- |
2 |
ULTRASONIC SENSOR CLIP |
89348D |
- |
- |
|
3 |
REAR CENTER ULTRASONIC SENSOR |
89342A |
- |
- |
- |
4 |
REAR CORNER ULTRASONIC SENSOR |
89342 |
- |
- |
- |
5 |
REAR CENTER ULTRASONIC SENSOR RETAINER |
89C48B |
- |
- |
|
6 |
REAR CORNER ULTRASONIC SENSOR RETAINER |
89C48A |
- |
- |
|
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
7 |
ULTRASONIC SENSOR CUSHION SET |
89305 |
- |
- |
|
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Ultrasonic sensor |
|
|
PROCEDURE
1. REMOVE REAR BUMPER ASSEMBLY
- except Sport Package:
Click here
.gif)
- for Sport Package:
Click here
.gif)
2. REMOVE ULTRASONIC SENSOR CLIP
*1 |
No. 6 Floor Wire |
- |
- |
(1) Disengage the clamp to separate the No. 6 floor wire.
(2) Using a screwdriver with its tip wrapped with protective tape, disengage the claws to remove the ultrasonic sensor clip.
(b) The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
3. REMOVE REAR CENTER ULTRASONIC SENSOR
(b) The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
4. REMOVE REAR CORNER ULTRASONIC SENSOR
(b) The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
5. REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER
![]() |
NOTICE:
|
(1) Heat the adhesive of the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.
Standard:
Item | Temperature | Item | Temperature |
|---|---|---|---|
Rear Bumper Assembly |
40 to 50 °C |
Rear Center Ultrasonic Sensor Retainer |
40 to 50 °C |
CAUTION:
- Do not touch the heat light and heated parts.
- Touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat the rear bumper assembly and rear center ultrasonic sensor retainer excessively.
HINT:
Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
(2) Remove the rear center ultrasonic sensor retainer.
(b) The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
6. REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER
![]() |
NOTICE:
|
(1) Heat the adhesive of the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.
Standard:
Item | Temperature | Item | Temperature |
|---|---|---|---|
Rear Bumper Assembly |
40 to 50 °C |
Rear Corner Ultrasonic Sensor Retainer |
40 to 50 °C |
CAUTION:
- Do not touch the heat light and heated parts.
- Touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat the rear bumper assembly and rear corner ultrasonic sensor retainer excessively.
HINT:
Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
(2) Remove the rear corner ultrasonic sensor retainer.
(b) The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
7. REMOVE ULTRASONIC SENSOR CUSHION SET
![]() |
NOTICE: Perform this procedure only when replacement of the ultrasonic sensor cushion set is necessary. |
.png)
.png)
.png)
.png)