Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PRECAUTION |
- |
- |
- |
|
2 |
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
3 |
FRONT WHEEL |
- |
- |
- |
- |
4 |
DRAIN BRAKE FLUID |
- |
- |
- |
|
*A |
for HEV Model |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
5 |
FRONT FLEXIBLE HOSE |
47313J |
- |
- |
- |
6 |
DISC BRAKE CYLINDER ASSEMBLY |
47750 |
- |
- |
- |
7 |
FRONT DISC BRAKE PAD KIT |
04465 |
- |
- |
- |
8 |
FRONT ANTI SQUEAL SHIM KIT |
04945 |
- |
- |
|
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
9 |
FRONT DISC BRAKE FITTING KIT |
04947 |
- |
- |
|
10 |
FRONT DISC BRAKE CYLINDER SLIDE PIN |
47715A |
- |
- |
- |
11 |
FRONT DISC BRAKE CYLINDER SLIDE BUSH |
47769 |
- |
- |
|
12 |
FRONT DISC BRAKE BUSHING DUST BOOT |
- |
- |
- |
- |
13 |
FRONT DISC BRAKE CYLINDER MOUNTING |
47722 |
- |
- |
- |
14 |
FRONT DISC |
43512 |
- |
- |
|
● |
Non-reusable part |
- |
- |
NOTICE:
- Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
- After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.
- After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.
- When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTCs may be stored. As there is no malfunction, clear the DTC. (for HEV Model)
- While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HEV Model)
- When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
Drive the vehicle straight ahead at 15 km/h or more for 5 second or more.

- Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Power door lock control system
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power back door system
Fully close the back door by hand.
HINT:
Initialization is not necessary if the above procedures are performed while the back door is closed.

Air conditioning system
After the ignition switch is turned to ON, the servo motor standard position is recognized.
-
- Learning completes when vehicle is driven
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION (for HEV Model)
![]() |
NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Click here |
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (for HEV Model)
Click here ![]()
3. REMOVE FRONT WHEEL
Click here ![]()
4. DRAIN BRAKE FLUID
![]() |
NOTICE: If brake fluid leaks onto any painted surface, immediately wash it off. |
5. DISCONNECT FRONT FLEXIBLE HOSE
6. REMOVE DISC BRAKE CYLINDER ASSEMBLY
7. REMOVE FRONT DISC BRAKE PAD KIT
8. REMOVE FRONT ANTI SQUEAL SHIM KIT
![]() |
Click here |
9. REMOVE FRONT DISC BRAKE FITTING KIT
![]() |
NOTICE: Each front disc brake pad support plate has a different shape. Be sure to put an identification mark on each front disc brake pad support plate so that it can be reinstalled to its original position. |
10. REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN
11. REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSH
(1) Using a screwdriver with its tip wrapped with protective tape, remove the front disc brake cylinder slide bush from the front disc brake cylinder slide pin (lower side).
NOTICE:
Do not damage the front disc brake cylinder slide pin.
12. REMOVE FRONT DISC BRAKE BUSHING DUST BOOT
13. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING
14. REMOVE FRONT DISC
*a |
Matchmark |
- |
- |
(1) Put matchmarks on the front disc and the front axle hub sub-assembly.
(2) Remove the front disc.


