Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
55400 |
- |
- |
- |
2 |
FRONT NO. 1 CONSOLE BOX INSERT |
58816D |
- |
- |
- |
3 |
NO. 1 AIR DUCT |
87211 |
- |
- |
|
4 |
BRAKE PEDAL STROKE SENSOR ASSEMBLY |
89510D |
- |
- |
|
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
5 |
STOP LIGHT SWITCH ASSEMBLY |
84340 |
- |
- |
|
6 |
BRAKE PEDAL RETURN SPRING |
47101A |
- |
- |
- |
7 |
PUSH ROD PIN |
47264A |
- |
- |
- |
8 |
BRAKE PEDAL SUPPORT ASSEMBLY |
47110 |
- |
- |
- |
9 |
STOP LIGHT SWITCH MOUNTING ADJUSTER |
84345 |
- |
- |
|
10 |
BRAKE PEDAL PAD |
47121 |
- |
- |
- |
*1 |
WIRE HARNESS |
- |
- |
● |
Non-reusable part |
- |
- |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake pedal support assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. | |||
Brake pedal*1 |
|
|
|
HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front camera system
Drive the vehicle straight ahead at 15 km/h or more for 1 second or more.
.gif)
- Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Power door lock control system
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
.gif)
Power back door system
Fully close the back door by hand.
HINT:
Initialization is not necessary if the above procedures are performed while the back door is closed.
.gif)
Air conditioning system
After the ignition switch is turned to ON, the servo motor standard position is recognized.
-
PROCEDURE
1. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Click here ![]()
2. REMOVE FRONT NO. 1 CONSOLE BOX INSERT
Click here ![]()
3. REMOVE NO. 1 AIR DUCT
![]() |
Click here |
4. REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY
![]() |
Click here |
5. REMOVE STOP LIGHT SWITCH ASSEMBLY
![]() |
Click here |
6. REMOVE BRAKE PEDAL RETURN SPRING
7. REMOVE PUSH ROD PIN
8. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY
9. REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER
![]() |
Click here |
10. REMOVE BRAKE PEDAL PAD

.png)
.png)
.png)