Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
FRONT WHEELS |
- |
- |
- |
- |
2 |
NO. 1 ENGINE UNDER COVER ASSEMBLY |
51410 |
- |
- |
- |
3 |
REAR ENGINE UNDER COVER LH |
51444A |
- |
- |
- |
4 |
REAR ENGINE UNDER COVER RH |
51443C |
- |
- |
- |
5 |
DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID |
- |
- |
- |
|
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
6 |
FRONT AXLE SHAFT NUT |
43502H |
- |
- |
|
7 |
FRONT SPEED SENSOR |
89543 |
- |
- |
|
8 |
TIE ROD END SUB-ASSEMBLY |
45047 |
- |
- |
|
9 |
FRONT STABILIZER LINK ASSEMBLY |
48810 |
- |
- |
|
10 |
FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY |
48069 |
- |
- |
- |
11 |
SEPARATE FRONT DRIVE SHAFT ASSEMBLY |
43420 |
- |
- |
|
*1 |
FRONT FLEXIBLE HOSE |
- |
- |
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
12 |
REMOVE FRONT DRIVE SHAFT ASSEMBLY |
43420 |
- |
- |
|
13 |
FRONT DRIVE SHAFT HOLE SNAP RING |
43420G |
- |
- |
|
● |
Non-reusable part |
- |
- |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front drive shaft assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplacement Part or Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
CVT fluid |
ATF thermal degradation estimate reset |
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly |
|
Bleed air from oil pump (continuously variable transaxle assembly) |
Stop and start system |
||
Front wheel alignment adjustment |
|
|
|
Suspension, tires, etc. |
Rear television camera assembly optical axis (Back camera position setting) |
Parking assist monitor system |
|
Initialize headlight ECU sub-assembly LH |
Automatic headlight beam level control system |
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE FRONT WHEELS
Click here ![]()
2. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here ![]()
3. REMOVE REAR ENGINE UNDER COVER LH
Click here ![]()
4. REMOVE REAR ENGINE UNDER COVER RH
Click here ![]()
5. DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID
Click here ![]()
6. REMOVE FRONT AXLE SHAFT NUT
(1) Using SST and a hammer, release the staked part of the front axle shaft nut.
SST: 09930-00010
NOTICE:
Loosen the staked part of the front axle shaft nut completely, otherwise the threads of the drive shaft may be damaged.
(2) While applying the brakes, using a 30 mm deep socket wrench, remove the front axle shaft nut.
7. SEPARATE FRONT SPEED SENSOR
![]() |
Click here |
8. SEPARATE TIE ROD END SUB-ASSEMBLY
![]() |
Click here |
9. SEPARATE FRONT STABILIZER LINK ASSEMBLY
![]() |
Click here |
10. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY
Click here ![]()
11. SEPARATE FRONT DRIVE SHAFT ASSEMBLY
![]() |
Click here |
12. REMOVE FRONT DRIVE SHAFT ASSEMBLY
(1) Using SST, remove the front drive shaft assembly.
SST: 09520-01011
SST: 09520-20010
09521-02010
09521-02040
09521-02060
NOTICE:
- Do not damage the front drive shaft oil seal.
- Do not damage the front axle inboard joint boot.
- Do not drop the front drive shaft assembly.
13. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING
(1) Using a screwdriver, remove the front drive shaft hole snap ring.
.png)
.png)
.png)
.gif)