Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
TAIL EXHAUST PIPE ASSEMBLY |
17430 |
- |
- |
- |
2 |
MAIN MUFFLER HEAT INSULATOR |
58327D |
- |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
3 |
FUEL TANK VENT HOSE SUB-ASSEMBLY |
77404A |
- |
- |
|
4 |
CHARCOAL CANISTER HOSE |
77759A |
- |
- |
- |
5 |
DISCONNECT CHARCOAL WITH OUTLET HOSE CANISTER ASSEMBLY |
77730B |
- |
- |
|
6 |
CANISTER (CHARCOAL CANISTER ASSEMBLY) |
77740 |
- |
- |
- |
7 |
FUEL TANK VENT HOSE |
77404 |
- |
- |
|
8 |
REMOVE CHARCOAL WITH OUTLET HOSE CANISTER ASSEMBLY |
77730B |
- |
- |
- |
9 |
LEAK DETECTION PUMP SUB-ASSEMBLY |
- |
- |
- |
|
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the canister (charcoal canister assembly) removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplacement Part or Procedure | Necessary Procedure | Effect/Inoperative when not Performed | Link |
|---|---|---|---|
Gas leaks from exhaust system is repaired |
Inspection After Repair |
|
PROCEDURE
1. REMOVE TAIL EXHAUST PIPE ASSEMBLY
Click here ![]()
2. REMOVE MAIN MUFFLER HEAT INSULATOR
3. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY
(1) Disconnect the fuel tank vent hose sub-assembly the canister (charcoal canister assembly).
Click here ![]()
4. DISCONNECT CHARCOAL CANISTER HOSE
5. DISCONNECT CHARCOAL WITH OUTLET HOSE CANISTER ASSEMBLY
(1) Disconnect the charcoal with outlet hose canister assembly from the canister (charcoal canister assembly).
Click here ![]()
6. REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY)
7. DISCONNECT FUEL TANK VENT HOSE
(1) Disconnect the fuel tank vent hose sub-assembly from the No. 2 charcoal canister filter.
Click here ![]()
8. REMOVE CHARCOAL WITH OUTLET HOSE CANISTER ASSEMBLY
9. REMOVE LEAK DETECTION PUMP SUB-ASSEMBLY
![]() |
HINT: Only perform this procedure when replacement of the leak detection pump sub-assembly is necessary. |
*a |
Protective Tape |
- |
- |
*1 |
No. 2 charcoal canister filter |
- |
- |
(1) Before removing the leak detection pump sub-assembly, clean the No. 1 charcoal canister filter by blowing air into it to ensure that the No. 1 charcoal canister filter is free of foreign matter.
NOTICE:
- Make sure to clean the charcoal canister sub-assembly using air only.
- Do not use gasoline, thinners or solvents.
(2) While disengaging the 2 claws as shown in the illustration, push the leak detection pump subassembly upwards using a screwdriver with its tip wrapped with protective tape to remove it.
(3) Check if the No. 2 charcoal canister filter contains foreign matter such as mud or water.
- Visually check that the inside of the No. 2 charcoal canister filter is free of foreign matter.
- Hold the No. 2 charcoal canister filter upside down to make sure that it is free of foreign matter.
- If the No. 2 charcoal canister filter contains foreign matter, replace the No. 1 charcoal canister filter.
.png)
.png)
.png)
.gif)