Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
INLET NO. 1 AIR CLEANER |
17751 |
- |
- |
- |
2 |
AIR CLEANER CAP WITH AIR CLEANER HOSE |
- |
- |
- |
- |
3 |
THROTTLE BODY WITH MOTOR ASSEMBLY |
22030 |
- |
- |
|
4 |
THROTTLE BODY GASKET |
22271 |
- |
- |
- |
5 |
No. 1 EGR PIPE SUB-ASSEMBKY |
25601 |
- |
- |
|
6 |
EGR VALVE ADAPTER GASKET |
25629 |
- |
- |
- |
7 |
EGR INLET GASKET |
25628 |
- |
- |
- |
8 |
E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR) |
89421 |
- |
- |
- |
9 |
ENGINE WIRE |
82121 |
- |
- |
- |
10 |
NO. 3 WATER BY-PASS PIPE |
16279 |
- |
- |
|
11 |
INTAKE MANIFOLD STAY |
17138B |
- |
- |
|
12 |
NO. 1 FUEL VAPOR FEED HOSE |
23826 |
- |
- |
- |
13 |
INTAKE MANIFOLD |
17111 |
- |
- |
- |
14 |
NO. 1 INTAKE MANIFOLD TO HEAD GASKET |
17177 |
- |
- |
- |
15 |
VACUUM HOSE |
- |
- |
- |
- |
*A |
w/ Stud bolt |
*B |
w/o Stud bolt |
● |
Non-reusable part |
- |
- |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
Inspection after repair |
|
NOTICE:
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
![]()
PROCEDURE
1. REMOVE INLET NO. 1 AIR CLEANER
Click here ![]()
2. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
Click here ![]()
3. SEPARATE THROTTLE BODY WITH MOTOR ASSEMBLY
(1) Disconnect the throttle body with motor assembly connector.
(2) Using an 8 mm socket wrench, remove the 3 bolts to separate the throttle body with motor assembly from the intake manifold.
4. REMOVE THROTTLE BODY GASKET
Click here ![]()
5. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
Click here
![]()
6. REMOVE EGR VALVE ADAPTER GASKET
Click here
![]()
7. REMOVE EGR INLET GASKET
Click here
![]()
8. REMOVE E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)
Click here ![]()
9. DISCONNECT ENGINE WIRE
10. SEPARATE NO. 3 WATER BY-PASS PIPE
(1) Using an 8 mm socket wrench, remove the bolt and separate the No. 3 water by-pass pipe from the intake manifold.
11. REMOVE INTAKE MANIFOLD STAY
(1) Using an 8 mm socket wrench, remove the bolt (A).
(2) Remove the bolt (B).
(3) Disengage the guide and remove the intake manifold stay.
12. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
13. REMOVE INTAKE MANIFOLD
(a) w/o Stud bolt
(b) w/ Stud bolt
(1) Remove the 3 bolts and 2 nuts.
(2) Using an E8 "TORX" socket wrench, remove the 2 stud bolts and separate the intake manifold from the cylinder head sub-assembly.
(3) Disconnect the fuel pressure sensor connector.
(4) Remove the intake manifold.
14. REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET
15. REMOVE VACUUM HOSE

.png)
.png)
.png)
.gif)