Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY |
77020A |
- |
- |
- |
2 |
DRAIN FUEL |
- |
- |
- |
|
3 |
TAIL EXHAUST PIPE ASSEMBLY |
17430 |
- |
- |
|
4 |
NO. 1 FUEL TANK PROTECTOR |
77641A |
- |
- |
- |
5 |
DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY |
77404A |
- |
- |
|
6 |
FUEL TANK FILLER PIPE ASSEMBLY |
77210 |
- |
- |
|
7 |
DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY |
77209F |
- |
- |
|
8 |
FUEL TANK ASSEMBLY |
77100 |
- |
- |
|
9 |
REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY |
77209F |
- |
- |
- |
10 |
REMOVE FUEL TANK VENT HOSE SUB-ASSEMBLY |
77404A |
- |
- |
- |
● |
Non-reusable part |
- |
- |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Gas leak from exhaust system is repaired |
Inspection after repair |
|
CAUTION:
- Never perform work on fuel system components near any possible ignition sources.
.png)
- Vaporized fuel could ignite, resulting in a serious accident.
- Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
.png)
- Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
- The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
.png)
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
Drive the vehicle straight ahead at 15 km/h or more for 1 second or more.
.gif)
- Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Power door lock control system
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
.gif)
Power back door system
Fully close the back door by hand.
HINT:
Initialization is not necessary if the above procedures are performed while the back door is closed.
.gif)
Air conditioning system
After the ignition switch is turned to ON, the servo motor standard position is recognized.
-
PROCEDURE
1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
Click here ![]()
2. DRAIN FUEL
3. REMOVE TAIL EXHAUST PIPE ASSEMBLY
![]() |
Click here |
4. REMOVE NO. 1 FUEL TANK PROTECTOR
5. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY
(1) Disconnect the fuel tank vent hose sub-assembly from the fuel vapor containment valve (fuel tank solenoid main valve assembly).
Click here ![]()
6. DISCONNECT FUEL TANK FILLER PIPE ASSEMBLY
(1) Disconnect the fuel tank filler pipe assembly from the fuel tank assembly.
Click here ![]()
7. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
(1) Disconnect the fuel tank main tube sub-assembly from the fuel pipe.
Click here ![]()
8. REMOVE FUEL TANK ASSEMBLY
![]() |
CAUTION: The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter. |
(1) Support the fuel tank assembly using an engine lifter.
HINT:
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
(2) Remove the 4 bolts.
(3) Lower the engine lifter to remove the fuel tank assembly.
NOTICE:
- Be careful not to drop the fuel tank assembly.
- When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
9. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
10. REMOVE FUEL TANK VENT HOSE SUB-ASSEMBLY

.png)
.png)
.png)