Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PRECAUTION |
- |
- |
- |
|
2 |
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
3 |
LOWER CENTER INSTRUMENT PANEL FINISH PANEL |
55434F |
- |
- |
- |
4 |
FRONT DOOR SCUFF PLATE LH |
67914B |
- |
- |
- |
5 |
COWL SIDE TRIM SUB-ASSEMBLY LH |
62112A |
- |
- |
- |
6 |
FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
62312B |
- |
- |
- |
7 |
NO. 1 INSTRUMENT SIDE PANEL |
55317E |
- |
- |
|
8 |
HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
53601 |
- |
- |
- |
9 |
LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
55432D |
- |
- |
- |
10 |
INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
55403F |
- |
- |
- |
11 |
INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
55410C |
- |
- |
- |
12 |
CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL |
55413D |
- |
- |
- |
13 |
INSTRUMENT CLUSTER FINISH PANEL RETAINER |
55416C |
- |
- |
- |
14 |
COMBINATION METER ASSEMBLY |
83100 |
- |
- |
- |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during combination meter assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
Combination meter assembly |
Update ECU security key |
Vehicle Control History (RoB) are stored |
HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for Gasoline Model Front Camera System
Drive the vehicle straight ahead at 15 km/h or more for 1 second or more.
.gif)
Stop and start system*1
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)
.gif)
- Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Power door lock control system
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
.gif)
Power back door system
Fully close the back door by hand.
HINT:
Initialization is not necessary if the above procedures are performed while the back door is closed.
.gif)
Air conditioning system
After the ignition switch is turned to ON, the servo motor standard position is recognized.
-
PROCEDURE
1. PRECAUTION
![]() |
NOTICE: After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-)auxiliary battery terminal. Click here |
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
- for M20A-FKS:
Click here
.gif)
- for M20A-FXS:
Click here
.gif)
3. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL
Click here ![]()
4. REMOVE FRONT DOOR SCUFF PLATE LH
Click here ![]()
5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Click here ![]()
6. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here ![]()
7. REMOVE NO. 1 INSTRUMENT SIDE PANEL
![]() |
Click here |
8. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Click here ![]()
9. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
Click here ![]()
10. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Click here ![]()
11. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Click here ![]()
12. REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
13. REMOVE INSTRUMENT CLUSTER FINISH PANEL RETAINER
Click here ![]()
14. REMOVE COMBINATION METER ASSEMBLY

.png)
.png)
.png)