Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PRECAUTION |
- |
- |
- |
|
2 |
CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
3 |
REAR CENTER SEAT OUTER BELT ASSEMBLY |
73350C |
- |
- |
- |
4 |
BENCH TYPE REAR SEAT CUSHION ASSEMBLY |
- |
- |
- |
|
5 |
REAR SEAT CUSHION LOCK HOOK |
72693 |
- |
- |
- |
*A |
for Gasoline Model |
- |
- |
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
6 |
FRONT DOOR SCUFF PLATE |
67914B |
- |
- |
- |
7 |
FRONT DOOR OPENING TRIM WEATHERSTRIP |
62312B |
- |
- |
- |
8 |
REAR DOOR SCUFF PLATE |
67918A |
- |
- |
- |
9 |
REAR DOOR OPENING TRIM WEATHERSTRIP |
62332A |
- |
- |
- |
10 |
LAP BELT OUTER ANCHOR COVER |
73233 |
- |
- |
- |
11 |
FRONT SEAT OUTER BELT ASSEMBLY |
73220 |
- |
- |
- |
12 |
CENTER PILLAR LOWER GARNISH |
62414A |
- |
- |
- |
13 |
CENTER PILLER GARNISH ASSEMBLY |
62420A |
- |
- |
- |
*A |
for Gasoline Model |
*B |
for HEV Model |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
14 |
FRONT SEAT OUTER BELT ASSEMBLY |
73220 |
- |
- |
|
15 |
FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY |
73200A |
- |
- |
- |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front seat outer belt assembly removal/installation are shown below.
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
- When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Learning completes when vehicle is driven
Effect / Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*A: for Gasoline Model Front Camera System
Drivre the vehicle straight ahead at 15 km/h or more for 1 second or more.
.gif)
Stop and start system *A
Drive the vehicle until stop and start control is permitted (appoximately 5 to 60 minutes)
.gif)
- Learning completes when vehicle is operated normally
Effect / Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Power door lock control system
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
.gif)
Power back door system
Fully close the back door by hand.
HINT:
Initialization is not necessary if the above procedures are performed while the back door is closed.
.gif)
Air conditioning system
After the ignition switch is turned to ON, the servo motor standard position is recognized.
-
- Learning completes when vehicle is driven
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
PROCEDURE
1. PRECAUTION
![]() |
CAUTION: Be sure to read Precaution thoroughly before servicing.
Click here NOTICE: After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal. Click here |
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
![]() |
|
- for Gasoline Model:
Click here
.gif)
- for HEV Model:
Click here
.gif)
3. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Gasoline Model)
Click here ![]()
4. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)
![]() |
Click here |
5. REMOVE REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)
Click here ![]()
6. REMOVE FRONT DOOR SCUFF PLATE
Click here ![]()
7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
8. REMOVE REAR DOOR SCUFF PLATE
Click here ![]()
9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
10. REMOVE LAP BELT OUTER ANCHOR COVER
11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY
12. REMOVE CENTER PILLAR LOWER GARNISH
Click here ![]()
13. REMOVE CENTER PILLER GARNISH ASSEMBLY
Click here ![]()
14. REMOVE FRONT SEAT OUTER BELT ASSEMBLY
(1) Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.
(2) Disconnect the pretensioner connector.
HINT:
Refer to How to Connector or Disconnect Airbag Connector:
Click here ![]()
(3) Remove the bolt.
(4) Disengage the 2 guides to remove the front seat outer belt assembly.
15. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

.png)
.png)
.png)