Toyota Corolla Quiz
Diagnostics

Circuit description

In this manual: Diagnostics
Introduction — 31Preparation — 32Service specifications — 19Diagnostics — 497Engine control system — 6Fuel — 13Emission control — 28Exhaust — 3Cooling — 13Lubrication — 7Ignition — 3Starting & charging — 13Front suspension — 12Rear suspension — 9Tire & wheel — 1Drive shaft / propeller shaft — 15Brake — 42Automatic transmission / trans — 47Clutch — 19Steering column — 9Power steering — 11Heater & air conditioner — 20Supplemental restraint system — 27Seat belt — 12Lighting — 18Wiper & washer — 9Audio & visual — 12Wiring — 1Communication system — 1Windshield/windowglass/mirror — 31Seat — 10Theft deterrent & door lock — 10Sliding roof/convertible — 8Engine hood/door — 12Exterior/interior trim — 20Vehicle control system — 1Cruise control — 5Maintenance — 8
20steps
~120min
4/5difficulty
Done 0 of 20
1 Check p squib circuit(airbag sensor assy center – instrument panel passenger airbag assy)
Toyota Corolla. Check p squib circuit
  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2. disconnect the connectors between the airbag sensor assy center and the instrument panel passenger airbag assy.
  3. for the connector (on the instrument panel passenger airbag assy side) between the airbag sensor assy center and the instrument panel passenger airbag assy, measure the resistance between p+ and p–.

    Ok: resistance: below 1 Ω

    2 Check air bag sensor assy center
2 Check air bag sensor assy center

Sst 09843–18040

Toyota Corolla. Check air bag sensor assy center
  1. Connect the connector to the airbag sensor assy center.
  2. using a service wire, connect p+ and p– of the connector (on the instrument panel passenger airbag assy side) between the airbag sensor assy center and the instrument panel passenger airbag assy.
  3. connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4. turn the ignition switch to on, and wait at least for 20 seconds.
  5. clear the dtc stored in memory .
  6. turn the ignition switch to lock, and wait at least for 20 seconds.
  7. turn the ignition switch to on, and wait at least for 20 seconds.
  8. check the dtc .

    Ok: dtc b0106/54 is not output.

Hint

: codes other than code b0106/54 may be output at this time, but they are not relevant to this check.
3 Check p squib
3 Check p squib

Sst 09843–18040

Toyota Corolla. Check p squib
  1. Turn the ignition switch to lock.
  2. disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3. connect the instrument panel passenger airbag assy connector.
  4. connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5. turn the ignition switch to on, and wait at least for 20 seconds.
  6. clear the dtc stored in memory .
  7. turn the ignition switch to lock, and wait at least for 20 seconds.
  8. turn the ignition switch to on, and wait at least for 20 seconds.
  9. check the dtc .

    Ok: dtc b0106/54 is not output.

Hint

: codes other than code b0106/54 may be output at this time, but they are not relevant to this check.
Use simulation method to check
Use simulation method to check

Test yourself

A quick Toyota Corolla quiz: every answer comes with an explanation and a link to the manual page.