Toyota Sienna Quiz
Supplemental restraint system

DTC check / clear

In this manual: Supplemental restraint system
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
18steps
~113min
5/5difficulty
1special tools
Done 0 of 18

1. DTC CHECK (USING SST CHECK WIRE)

DTC CHECK
  1. Check the DTCs (Present trouble code).
  2. Turn the ignition switch ON, and wait for approximately 60 seconds.
  3. Using SST, connect terminals TC and CG of the DLC3.

    SST 09843-18040

NOTICE: Connect the terminals to the correct positions to avoid a malfunction.

  1. Check the DTCs (Past trouble code).
  2. Using SST, connect terminals TC and CG of the DLC3.

    SST 09843-18040

NOTICE: Connect the terminals to the correct positions to avoid a malfunction.

  1. Turn the ignition switch ON, and wait for approximately 60 seconds.
    DTC CHECK
  2. Read the DTCs.
  3. Read the blinking patterns of the DTCs. As examples, the blinking patterns for the normal system code and trouble codes 11 and 31 are shown in the illustration.
  • Normal system code indication (w/o past trouble code) The light blinks twice per second.
  • Normal system code indication (w/ past trouble code) When the past trouble code is stored in the center airbag sensor assembly, the light blinks only once per second.
  • Trouble code indication The first two blinkings indicate the first DTC. The second blinking occurs after a 1.5- second pause.

    If there are more than 1 code, there will be a 2.5- second pause between each code. After all codes are shown, there will be a 4.0-second pause, and they all will be repeated.

HINT:

  • If 2 or more malfunctions are found, the indication begins with the smaller numbered code.
  • If DTCs are indicated without connecting the terminals, proceed to the "Diagnosis Circuit"

2. DTC CLEAR (USING SST CHECK WIRE)

  1. Clear the DTCs.
  2. When the ignition switch is turned off, the DTCs are cleared.
HINT: Depending on the DTC, the code may not be cleared by turning off the ignition switch. In this case, proceed to the next procedure.
  • Using SST, connect terminals TC and CG of the DLC3, and then turn the ignition switch to the ON position.

    SST 09843-18040

  • Disconnect terminal TC of the DLC3 within 3 to 10 seconds after the DTCs are output, and check if the SRS warning light comes on after 3 seconds.
  • Within 2 to 4 seconds after the SRS warning light comes on, connect terminals TC and CG of the DLC3.
  • The SRS warning light should go off within 2 to 4 seconds after connecting terminals TC and CG of the DLC3. Then, disconnect terminal TC within 2 to 4 seconds after the SRS warning light goes off.
  • The SRS warning light comes on again within 2 to 4 seconds after disconnecting terminal TC.

    Then, reconnect terminals TC and CG of the DLC3 within 2 to 4 seconds after the SRS warning light comes on.

  • Check if the SRS warning light goes off within 2 to 4 seconds after connecting terminals TC and CG of the DLC3. Also check if the normal system code is output within 1 second after the SRS warning light goes off.

    If DTCs are not cleared, repeat this procedure until the codes are cleared.

    • DTC CLEAR

    3. DTC CHECK

    DTC CHECK
    1. Check the DTCs.
    2. Connect the intelligent tester to the DLC3.
    3. Turn the ignition switch to the ON position.
    4. Check the DTCs by following the prompts on the tester screen.

    HINT: Refer to the intelligent tester operator's manual for further details.

    1. Clear the DTCs.
    2. Connect the intelligent tester to the DLC3.
    3. Turn the ignition switch to the ON position.
    4. Clear the DTCs by following the prompts on the tester screen.

    HINT: Refer to the intelligent tester operator's manual for further details.

    Test yourself

    A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.