Toyota Sienna Quiz
Seat belt

Installation

In this manual: Seat belt
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
11steps
~66min
3/5difficulty
Done 0 of 11

1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

  1. Install the front shoulder belt anchor adjuster assembly with the bolt.

    Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)

2. INSTALL CENTER PILLAR UPPER GARNISH

3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

INSTALL FRONT SEAT OUTER BELT ASSEMBLY

NOTICE: Do not disassemble the retractor.

  1. Check the degree of tilt when beginning to lock the ELR.
  2. Check that the belt does not lock within 15 degrees of tilt in all directions but that the belt locks with over 45 degrees of tilt, when gently moving the retractor.

    If operation is not as specified, replace the front seat outer belt assembly.

  3. Install the retractor with the 2 bolts.

    Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)

  4. Install the shoulder anchor with the nut.

    Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)

  5. Install the floor anchor with the bolt.

    Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)

  6. Install the floor anchor cover.
  7. Check the ELR lock.

NOTICE: The check should be performed with the assembly installed.

  1. Check that the belt locks when pulling out the belt quickly when the belt is installed.

    If operation is not as specified, replace the front seat outer belt assembly.

  2. Check the fastening function of the child restraint system.

NOTICE: The check should be performed with the assembly installed.

  1. Check that the belt cannot be pulled out any more but can be rewound after the belt is fully pulled out.
  2. Check that the belt can be pulled out and rewound after the belt is fully rewound.

    If operation is not as specified, replace the front seat outer belt assembly.

4. INSTALL CENTER PILLAR LOWER GARNISH

5. INSTALL FRONT DOOR WEATHERSTRIP

6. INSTALL REAR DOOR WEATHERSTRIP

7. INSTALL FRONT DOOR SCUFF PLATE

8. INSTALL REAR DOOR SCUFF PLATE

9. INSTALL FRONT SEAT ASSEMBLY

HINT:

  • Refer to the instructions for installation of the front seat assembly (for flat type).
  • Refer to the instructions for installation of the front seat assembly (for manual seat).
  • Refer to the instructions for installation of the front seat assembly (for power seat).

10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

11. PERFORM INITIALIZATION

HINT: Some systems need initialization when disconnecting the cable from the negative battery terminal.

Test yourself

A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.