Toyota Tacoma Quiz
Suspension

Removal

In this manual: Suspension
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~2min read
4special tools
REMOVAL CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The procedure listed below is for the LH side.
PROCEDURE

1. REMOVE FRONT WHEEL

2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

3. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

(a) Remove the nut and separate the front stabilizer link assembly LH from the steering knuckle.

HINT:

If the ball joint turns together with the nut, use a socket hexagon wrench 6 mm to hold the stud.

4. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure for the RH side and LH side.

5. REMOVE FRONT NO. 1 STABILIZER BRACKET LH

6. REMOVE FRONT NO. 1 STABILIZER BRACKET RH

6. REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Use the same procedure for the RH side and LH side.

7. REMOVE FRONT STABILIZER BAR

8. SEPARATE TIE ROD END SUB-ASSEMBLY

9. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING 9. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

9. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

(a) Remove the bolt, nut and the washer on the lower side of the front shock absorber with coil spring.

(b) Remove the 3 nuts on the upper side of the front shock absorber with coil spring.

(c) Remove the front shock absorber with coil spring.

10. REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

(a) Secure SST in a vise.

SST: 09727-00060

SST: 09727-30021

09727-00010

09727-00031

(b) Attach the arm of SST to the diameter of the front coil spring.

CAUTION:

  • Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
  • Make sure that the claws of the hooks are securely attached.

(c) Using SST, compress the front coil spring.

CAUTION:

  • If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.
  • Do not compress the spring until the coil springs contact each other.
  • Do not use an impact wrench. It will damage SST.

(d) Confirm that the front coil spring becomes free and while holding the shock absorber rod, remove the front support to front shock absorber nut.

CAUTION:

Do not remove the front support to front shock absorber nut when the front coil spring is not free.

11. REMOVE FRONT SHOCK ABSORBER CUSHION RETAINER

12. REMOVE FRONT SHOCK ABSORBER NO. 1 CUSHION

13. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

14. REMOVE FRONT SHOCK ABSORBER CUSHION RETAINER

15. REMOVE FRONT COIL SPRING

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.