1. PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED / RECONNECTED
Procedures Necessary when Cable is Disconnected/Reconnected to Battery Terminal
Necessary Procedure
Effect or Inoperative Function when Necessary Procedure is not Performed
See page
Gain acquisition mode and trailer brake type setting
Initial value Gain value is set to 5.0 (initial value)
Memorize steering angle neutral point
Lane departure alert system
Pre-collision system
NOTICE:
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.
2. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Replacement Part
Necessary Procedures
Effects / Inoperative Functions When Necessary Procedures are not Performed
See Page
for 1UR-FE:
Throttle body assembly
Cleaning the deposits from the throttle body assembly
Engine assembly
Cylinder head sub-assembly
Camshaft (for intake or exhaust camshaft)
Camshaft timing gear assembly
Camshaft timing exhaust gear assembly
Piston or piston ring
Mass air flow meter sub-assembly
Fuel injector assembly
Fuel pump
Air fuel ratio sensor
Heated oxygen sensor
Engine coolant temperature sensor
Spark plug
Ignition coil assembly
Air leaks from intake system
Gas leaks from exhaust system
Knock control sensor
Initialization
Engine control system
for 3UR-FE, 3UR-FBE:
Throttle body assembly
Cleaning the deposits from the throttle body assembly
Engine assembly
Cylinder head sub-assembly
Camshaft (for intake or exhaust camshaft)
Camshaft timing gear assembly
Camshaft timing exhaust gear assembly
Piston or piston ring
Mass air flow meter sub-assembly
Fuel injector assembly
Fuel pump
Air fuel ratio sensor
Heated oxygen sensor
Engine coolant temperature sensor
Spark plug
Ignition coil assembly
Air leaks from air induction system
Gas leaks from exhaust system
Knock sensor
Initialization
Engine control system
(for 3UR-FE)
(for 3UR-FBE)
ECM
Register VIN
DTC P0630 is output
(for 1UR-FE)
(for 3UR-FE)
(for 3UR-FBE)
for 3UR-FBE:
Fuel with different alcohol concentration is used
Reset fuel density learning value
Engine starting
Rough idling
Millimeter wave radar sensor assembly
Adjust millimeter wave radar sensor assembly
Dynamic radar cruise control system
Forward recognition camera system
Lane departure alert system
Pre-collision system
Forward recognition camera
Windshield glass
Adjust forward recognition camera
Dynamic radar cruise control system
Forward recognition camera system
Lane departure alert system
Pre-collision system
Automatic high beam system
Automatic transmission assembly
Valve body assembly
Any of the shift solenoid valves
Reset memory
Large shift shock
(for AB60F)
(for AB60E)
(for A760F)
(for A760E)
Automatic transmission fluid
ATF thermal degradation estimate reset
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.
Tire pressure warning ECU
Register transmitter IDs
Initialize tire pressure warning system
When DTC detection conditions of "transmitter ID not received" DTC is met, tire pressure warning light blinks for 1 minute, and then illuminates
Tire pressure monitoring function
(for Registration)
(for Initialization)
Tire pressure warning valve and transmitter
Register transmitter IDs
Initialize tire pressure warning system
When DTC detection conditions of "transmitter ID not received" DTC is met, tire pressure warning light blinks for 1 minute, and then illuminates
Tire pressure monitoring function of replaced wheel
Skid control ECU (brake actuator assembly)
Perform system variant learning and acceleration sensor zero point calibration
ABS warning light illumination
Slip indicator light illumination
Yaw rate and acceleration sensor (airbag ECU assembly)
ABS warning light illumination
Slip indicator light illumination
VSC control is prohibited or operation is incorrect
Wheel alignment adjustment
ABS warning light illumination
Slip indicator light illumination
Brake Control with Bracket Relay
Gain value setting
Initial value Gain value is set to 5.0 (initial value)
Blind spot monitor sensor
Blind spot monitor beam axis adjustment
DTCs are output
Blind spot monitor system
Occupant classification ECU
Zero point calibration
Sensitivity check
Occupant classification system
Passenger airbag ON/OFF indicator
Airbag system (Front passenger side)
Seat belt warning system (Front passenger side)
Transponder key ECU
ECM
Key
Registration
Engine starting
Door control transmitter
Door control receiver
Register recognition code
Wireless door lock operation
Power window regulator motor (Driver side)
Power window regulator motor (Passenger side)
Initialize the motor
Jam Protection Function
Power window control system (w/ Jam protection function)
Inner rear view mirror
Register transmitter code
Garage door opener system
Sliding roof drive gear (Sliding roof ECU)
Sliding roof housing
Sliding roof glass
Initialize sliding roof system
Auto operation
Jam protection function
Sliding roof operation after ignition switch is turned OFF
Key-linked operation function (Driver side door only)