Toyota Venza Quiz
Supplemental Restraint Systems

Removal

In this manual: Supplemental Restraint Systems
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
REMOVAL CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The procedure listed below is for the LH side.
PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page ).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).


3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


4. REMOVE DECK BOARD ASSEMBLY


5. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


6. REMOVE DECK SIDE TRIM BOX LH


7. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


8. REMOVE DECK SIDE TRIM BOX RH


9. REMOVE NO. 1 DECK BOARD


10. REMOVE REAR SEAT SUB FLOOR PANEL ASSEMBLY


11. REMOVE REAR FLOOR FINISH PLATE


12. REMOVE RECLINING REMOTE CONTROL BEZEL


13. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY


14. REMOVE REAR DOOR SCUFF PLATE


15. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


16. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY


17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY


18. REMOVE REAR AIRBAG SENSOR

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Disconnect the connector from the rear airbag sensor.

NOTICE:

When disconnecting the airbag connector, take care not to damage the airbag wire harness.

(1) Push and hold the white housing lock, and slide the yellow outer connector locking sleeve.

Text in Illustration

*1

Housing Lock

*2

Outer Connector Locking Sleeve

(2) Push and hold the white housing lock again, and slide the yellow outer connector locking sleeve to disconnect the connector.

(d) Remove the nut and rear airbag sensor.

NOTICE:

Loosen the nut while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.