Multi-function display (MFA)
and safety warnings first⇒
to the topic
The multi-function display (MFA) is equipped with 2 automatic memories: 1 – Single trip memory and 2 – Total trip memory. The number of the displayed memory appears at the bottom right of the display.
| With the ignition on and memory 1 or 2 displayed, press the button to switch between the two memories. |
||
|---|---|---|
| 1 | Single trip memory. | From switching the ignition on until switching it off, the memory collects the trip and consumption values. If the trip is interrupted for more than 2 hours, the memory is erased automatically. If the trip is continued within 2 hours after switching off the ignition, the newly added values are included. |
| 2 | Total trip memory. | Depending on the version of the instrument cluster, the memory collects the trip values of any number of single trips up to a total of 19 hours and 59 minutes of driving time or 1999.9 km or miles of distance. If one of these maximum values is exceeded, the memory is erased automatically and starts again at 0. |
| Menu | Function |
|---|---|
| Timea) | Current time in hours (h) and minutes (min). |
| Driving time | Driving time in hours (h) and minutes (min) that has elapsed since switching on the ignition. |
| Instantaneous fuel consumption | Instantaneous fuel consumption is shown in l/100 km while driving, and in litres per hour while the engine is running and the vehicle is stationary. For natural gas engines, it is shown in kg/100 km and kg/h. |
| Average consumption | Average fuel consumption in l/100 km, or in kg/100 km for natural gas engines, is not shown after switching on the ignition until a distance of approx. 100 metres has been driven. Until then, dashes are shown. The displayed value updates approx. every 5 seconds. |
| Range | Approximate driving range in km that can still be covered with the fuel remaining in the tank at the same driving style. The instantaneous fuel consumption is one of the factors used in this calculation. For natural gas engines: The value with the symbol |
| Distance travelled | Distance travelled in km since switching on the ignition. |
| Average speed | The average speed is not shown after switching on the ignition until a distance of approx. 100 metres has been driven. Until then, dashes are shown. The displayed value updates approx. every 5 seconds. |
| Digital speed display | Current driving speed as a digital display. |
| Digital coolant temperature display | Current engine coolant temperature as a digital display. If --.- appears in the instrument cluster display and the red warning lamp in the engine cooling system. continue driving! Seek assistance from a qualified workshop. |
| Digital outside temperature display | Current outside temperature as a digital display. |
| Warning at --- km/h | When the stored speed is exceeded (in the range between 30 km/h and 250 km/h), an audible and, where applicable, a visual warning is given. |
| Depending on the market, this warning is also given at speeds above 120 km/h. This warning is required by law and must not be changed. |
- Press the rocker switch on the wiper lever ⇒ Fig. 12② .
- Button

Press and hold the button on the wiper lever
⇒ Fig. 12① to select the hour display so that it flashes.
- Use the rocker switch on the wiper lever ⇒ Fig. 12② to set the time. Press it up or down to increase or decrease the hour display.
- Button

Briefly press the button on the wiper lever
to switch to the minute display so that it flashes.
- Use the rocker switch on the wiper lever to set the time. Press it up or down to increase or decrease the minute display.
- Button

Briefly press the button on the wiper lever
to finish setting the time.
The time can also be set directly using the adjustment buttons on the instrument cluster ⇒ .
Storing the speed for the speed warning- Select the Warning at --- km/h display.
- Button

Press the button on the wiper lever
to store the current speed and activate the warning.
- If necessary, within approx. 5 seconds, use the rocker switch on the wiper lever to set the desired speed. Then press

the button again or wait a few
seconds. The speed is stored and the warning is activated.
- To deactivate


Press the button. The stored speed is erased.
- Select the memory to be erased.
- Button

Press and hold the button for approx. 2
seconds ⇒ Fig. 12① .
Depending on the vehicle, additional Multifunction Display functions may be shown on the screen of the portable infotainment system (supplied by Volkswagen) ⇒ Accessories, Replacement Parts, Repairs and Modifications.
a) Only with instrument cluster version 2 ⇒ Instrument cluster.