Body

Attachments, Removing and Installing

~9min read

Lock Carrier Cover, Removing and Installing

Special tools and workshop equipment required

  • Pry Lever -80-200-

Removing

- Remove the expanding rivets -1- with a Pry Lever -80-200-.

- Remove the lock carrier cover -3- from the groove in the lock carrier -2--arrow-.

- Move the lock carrier cover forward and remove it.

  • While doing this, the tabs -6- on the radiator grille -5- will detach from the bumper cover -4-.

Installing

Install in reverse order of removal. Note the following:

- Slide the lock carrier cover into the groove in the lock carrier cover and then push it onto the radiator grille and bumper cover.

A63-10373

Center Reinforcement Brace, Removing and Installing, Vehicles through MY 2014

Removing

- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".

- Remove the mount for the Night Vision System Camera -R212- and free up the windshield washer fluid hose, if equipped. Refer to → Chapter "Night Vision System Camera -R212- Mount, Removing and Installing, Vehicles through MY 2014".

- Carefully remove the clips -2 and 3- from the guide tab with a screwdriver.

- Remove the bolts -arrows-.

- Release the catch -4- and remove the reinforcement brace -1- to the rear.

Installing

Install in reverse order of removal. Note the following:

- Install the mount for the Night Vision System Camera -R212-. Refer to → Chapter "Night Vision System Camera -R212- Mount, Removing and Installing, Vehicles through MY 2014".

A63-10717

Side Reinforcement Brace, Removing and Installing, Vehicles through MY 2014

Removing

- Remove the center reinforcement brace. Refer to → Chapter "Center Reinforcement Brace, Removing and Installing, Vehicles through MY 2014".

- Remove the bracket for the headlamp washer system spray nozzle. Refer to → Electrical Equipment; Rep. Gr.92; Headlamp Washer System; Spray Nozzles, Removing and Installing.

- Carefully remove the clips -2- from the guide tab with a screwdriver.

- Release the catch -arrow- and remove the reinforcement brace -1- to the rear.

Installing

Install in reverse order of removal.

A63-10718

Night Vision System Camera -R212- Mount, Removing and Installing, Vehicles through MY 2014

Removing

- Remove the lock carrier cover. Refer to → Chapter "Lock Carrier Cover, Removing and Installing".

- Disconnect the connector -1-.

- Remove the screws -2, 3, 5 and 6- and then remove the mount -4- with the Night Vision System Camera -R212-.

- Open the clamp -7--arrow- and remove the windshield washer fluid hose.

- If the mount is being replaced, then remove the Night Vision System Camera -R212-. Refer to → Communication; Rep. Gr.91; Infrared System; Night Vision System Camera, Removing and Installing.

Installing

Install in reverse order of removal.

A63-10507

Night Vision System Camera -R212- Mount, Removing and Installing, Vehicles from MY 2015

Removing

- Remove the lock carrier cover. Refer to → Chapter "Lock Carrier Cover, Removing and Installing".

- Disconnect the connector -2-.

- Remove the screws -1, 3 and 5- and then remove the mount -4- with the Night Vision System Camera -R212-.

- Open the clamp -6--arrow- and remove the washer fluid hose.

- If the mount is being replaced, then remove the Night Vision System Camera -R212-. Refer to → Communication; Rep. Gr.91; Infrared System; Night Vision System Camera, Removing and Installing.

Installing

Install in reverse order of removal.

A63-10992

Front Bumper Cover End Plate, Removing and Installing, Audi A6/S6

Removing

- Remove the bolts -2 and 4- and -arrows-.

- Remove the front bumper cover end plate -3- toward the rear and free up the wiring harness -1-.

- If installed, free up the water line for cleaning the headlamps.

- Remove the bumper cover end plate.

Installing

Install in reverse order of removal.

A63-10508

Front Bumper Cover End Plate, Removing and Installing, Audi RS 6

Removing

- Remove the bolts -2- and -arrows-.

- Remove the front bumper cover end plate -3- toward the rear and free up the wiring harness -1-.

- Remove the bumper cover end plate.

Installing

Install in reverse order of removal.

A63-10715

Spoiler Lip, Removing and Installing

Removing

- Remove the front bumper cover end plate. Refer to → Chapter "Attachments, Removing and Installing".

Caution

Danger of causing damage to the lip on the spoiler.

Coat the tabs on the spoiler lip with soapy water.

- Starting on the outer side, release the tabs -3- on the lip of the spoiler -1--arrows-.

- Remove the spoiler lip carefully from the mount -2-.

Installing

Install in reverse order of removal.

A63-10477

Spoiler Lower Section, Removing and Installing

Removing

- Remove the front bumper cover end plate. Refer to → Chapter "Front Bumper Cover End Plate, Removing and Installing, Audi RS 6".

- Remove the lower radiator air duct.

- Remove the bolts -arrows-.

A63-10716

- Remove spoiler lower part -1- on the outside starting at the bumper -arrow-.

Installing

Install in reverse order of removal.

A63-10875

Spoiler Lower Section Mount, Removing and Installing

Removing

- Remove the spoiler lower section. Refer to → Chapter "Spoiler Lower Section, Removing and Installing".

- Remove the bolts -arrows-.

- Pull the mount -1- slightly rearward and free up the wiring harness -2-.

- Remove the bracket.

Installing

Install in reverse order of removal.

A63-10876

Front Bumper Cover Mount, Removing and Installing

Removing

- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".

- Loosen the bolt -2- three turns.

- Free up the wiring harness -1-.

- Remove the bolts -3 and 5- and the mount -4- for the front bumper cover.

Note

Depending on the version, instead of bolts nuts may be installed.

Installing

Install in reverse order of removal. Note the following:

- Check the gap dimensions. Refer to → Chapter "Front Bumper Cover Gap Dimensions".

A63-10501

Molded Foam Part, Removing and Installing, Audi A6/S6 through MY 2014

Special tools and workshop equipment required

  • Pry Lever -80-200-

Removing

- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".

- Pry off the clip -1- using the Pry Lever - 80-200-

- Move the molded foam piece -2- in direction of -arrow- and disengage the tabs -3-.

- Remove the molded foam part.

Installing

Install in reverse order of removal.

A63-10502

Molded Foam Part, Removing and Installing, Audi A6 from MY 2015

Special tools and workshop equipment required

  • Pry Lever -80-200-

Removing

- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".

- Pry off the clip -1- using the Pry Lever - 80-200-

- Guide the molded foam part -2- out of the bracket -3- and remove.

Installing

Install in reverse order of removal.

A63-11016

Molded Foam Part, Removing and Installing, Audi RS 6

Removing

- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".

- Release the retainer -arrow A- and disengage the molded foam part -1- by moving the top of the molded foam part in the direction of -arrow B-.

- Remove the molded foam part.

Installing

Install in reverse order of removal.

A63-10719

Molded Foam Part Mount, Removing and Installing, Audi RS 6

Removing

- Remove the license plate.

- Remove screws -2- and -3- on the license plate holder -1-.

- Remove the molded foam part. Refer to → Chapter "Molded Foam Part, Removing and Installing, Audi RS 6".

- Remove the center reinforcement brace. Refer to → Chapter "Center Reinforcement Brace, Removing and Installing, Vehicles through MY 2014".

A63-10877

- Remove the bolts -arrows-.

- Remove the mount -1-.

Installing

Install in reverse order of removal.

A63-10878

Headlamp Washer System Spray Nozzle Cover, Removing and Installing

Removing

- Remove the headlamp washer system spray nozzle. Refer to → Electrical Equipment; Rep. Gr.92; Headlamp Washer System; Spray Nozzles, Removing and Installing.

- Expand the retainers -2- on the spray nozzle cover -1- with a screwdriver -arrows- and remove the spray nozzle -3-.

Note

Tabs will break off when expanding the retainers -4-.

A63-10503

Installing

Install in reverse order of removal. Note the following:

- Insert the spray nozzle -1- into the cover -2- as illustrated and then push on it in direction of -arrow- until it clicks into place.

A63-10534

Air Intake Grille, Removing and Installing

Removing

- Remove the air intake grille -1- from the bumper cover -arrow-.

Installing

Install in reverse order of removal.

A63-10535

Outer Air Intake Grille, Removing and Installing, Audi RS 6

Removing

- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".

- Press off the spiral clips -1 and 5- and free up the wiring harness -3-.

- Press off the cover -8- from the bumper cover, to do this push the catches -2, 4, 6, and 7- slightly to the side -arrow-.

A63-10721

- Carefully remove the clips -arrows- from the guide tab with a screwdriver.

- Remove the trim -1- from the bumper cover -2-.

A63-10720

- Release the catches -1, 4, and 5--arrow- and the air intake grille -3- from the bumper cover -2-.

Installing

Install in reverse order of removal.

A63-10722

Inner Air Intake Grille, Removing and Installing, Audi RS 6

Removing

- Pull air intake grille -1- off of the bumper cover -arrow- and remove it.

Note

If the air intake grille cannot be removed in the described manner, the front bumper cover must be removed. Refer to → Chapter "Bumper Cover, Removing and Installing".

Installing

Install in reverse order of removal. Note the following:

- The retaining tabs must engage completely in the bumper.

A63-10655

Outside Air Temperature Sensor -G17- Bracket, Removing and Installing

Removing

- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".

- Remove the Outside Air Temperature Sensor -G17-. Refer to → Electrical Equipment; Rep. Gr.90; Instrument Cluster; Outside Air Temperature Sensor, Removing and Installing.

- Remove the expanding pin -2- and the bracket -1-.

Installing

Install in reverse order of removal.

A63-10480