Body

Impact Member, Removing and Installing

~6min read

Impact Member, Removing and Installing

Removing

Note

When installing, bring all cable ties back to same positions.

- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".

- Remove the headlamp housing. Refer to → Electrical Equipment; Rep. Gr.94; Headlamp; Headlamp, Removing and Installing.

- If equipped, open the tabs -A arrows- and remove the air guide -1--B arrow-.

A19-10441

- Disconnect the connector from the Outside Air Temperature Sensor -G17--item 1- and A/C Pressure/Temperature Sensor -G395--item 4- and free up the wiring harness -3-.

- Remove the nuts and bolts -5- upward.

- Remove the impact bar -2- from the mounts.

Note

Pry the impact bar out of the mounts if it is not easy to remove.

- If the impact member is being replaced, then remove the bracket for the Outside Air Temperature Sensor -G17-. Refer to → Chapter "Outside Air Temperature Sensor -G17- Bracket, Removing and Installing".

Installing

Install in reverse order of removal.

A63-10408

Connecting Brace, Removing and Installing

Special tools and workshop equipment required

  • Drill
  • Drill 5 mm diameter.

Removing

- Remove the bumper cover mount. Refer to → Chapter "Bumper Cover Mount, Removing and Installing, Vehicles through MY 2014".

- Disconnect the connector -5- to the front airbag crash sensor. Pay attention to the Safety Precautions. Refer to → Body Interior; Rep. Gr.00; Safety Precautions; Pyrotechnic Components Safety Precautions.

- Disconnect the connector -1- from the horn.

- Remove the bolt -4- and the horn bracket.

- Drill out the blind rivet head -3- and strike the rivet shaft out.

- Loosen the bolt -6-, remove the bolt -2- and remove the connecting brace -7-.

Installing

Install in reverse order of removal.

A63-10514

Left Impact Member Mount, Removing and Installing

Removing

- Remove the front noise insulation. Refer to → Chapter "Front Noise Insulation, Removing and Installing".

- Remove the left front wheel spoiler. Refer to → Chapter "Front Wheel Housing Liner, Removing and Installing".

- Remove the impact member. Refer to → Chapter "Impact Member, Removing and Installing".

- Remove the connecting brace. Refer to → Chapter "Connecting Brace, Removing and Installing".

- On vehicles with a gasoline engine, move the left cooler for charge air cooling circuit with the coolant hoses still connected to the rear. Refer to → Engine Mechanical, Fuel Injection and Ignition; Rep. Gr.19; Radiator/Coolant Fan; Charge Air Cooling Circuit Radiator, Removing and Installing.

- On vehicles with 3.0L TDI engine (EA 897 Gen I) remove the charge air cooler. Refer to → Engine Mechanical, Fuel Injection and Glow Plug; Rep. Gr.21; Charge Air System; Charge Air Cooler, Removing and Installing.

- If equipped loosen the crossmember. Refer to → Engine Mechanical, Fuel Injection and Ignition; Rep. Gr.10; Subframe Mount; Overview - Subframe Mount.

- If equipped, remove the horn bracket. Refer to → Electrical Equipment; Rep. Gr.90; Horn; Overview - Horn.

- Remove the bolts -arrows-.

A63-10515

- Have a second technician open the clamps -1- in direction of -arrow A- and remove the condenser -2- from the mounts on the radiator -B arrows-.

Caution

There is a risk of damaging the condenser and refrigerant lines and hoses.

Do not bend, twist or stretch the refrigerant lines and hoses.

- Move the condenser with the lines still connected, forward and then to the side and then secure it.

A87-10374

- Mark the installation position of the mount to the lock carrier for installation later.

- Drill out the blind rivet and strike out the rivet shaft.

- Remove the bolts -arrows-.

- Move the lock carrier -2- slightly to the front and remove the impact member mount -1- to the left.

Installing

Install in reverse order of removal. Note the following:

- Tighten the impact member mount according to the marking made during removal.

- To rivet the bracket on the lock carrier, the radiator and fan shroud must be removed. Refer to → Rep. Gr.19; Radiator/Coolant Fan; Radiator, Removing and Installing.

A63-10409

Right Impact Member Mount, Removing and Installing

Removing

- Remove the front noise insulation. Refer to → Chapter "Front Noise Insulation, Removing and Installing".

- Remove the right wheel spoiler. Refer to → Chapter "Front Wheel Spoiler, Removing and Installing".

- Remove the impact member. Refer to → Chapter "Impact Member, Removing and Installing".

- Remove the connecting brace. Refer to → Chapter "Connecting Brace, Removing and Installing".

- Disconnect the connector -5- on the horn and remove the horn bracket. Refer to → Electrical Equipment; Rep. Gr.90; Horn; High Tone Horn H2/Low Tone Horn H7, Removing and Installing.

- If the vehicle has an auxiliary heater, remove the nut -4- and free up the coolant lines.

- Press the release, push the connector down and then free up the connectors -2 and 3- on the brackets.

- If the vehicle has a secondary air injection pump motor, then press the release button and remove the hose from the secondary air injection pump -1-.

- On vehicles with 3.0L TDI engine (EA 897 Gen I) remove the charge air cooler. Refer to → Rep. Gr.21; Charge Air System; Charge Air Cooler, Removing and Installing.

- If equipped loosen the crossmember. Refer to → Engine Mechanical, Fuel Injection and Ignition; Rep. Gr.10; Subframe Mount; Overview - Subframe Mount.

A63-10410

- Push the retainer back -arrow-, press the release down and disconnect the coolant fan connectors -1- and -2-, if applicable.

A19-11112

- Remove the bolts -arrows-.

A63-10483

- Mark the installation position of the mount to the lock carrier for installation later.

- Drill out the blind rivet and strike out the rivet shaft.

- Remove the bolts -arrows-.

- Move the lock carrier -1- slightly to the front and remove the impact member mount -2- to the right.

Installing

Install in reverse order of removal. Note the following:

- Tighten the impact member mount according to the marking made during removal.

- To rivet the bracket on the lock carrier, the radiator and fan shroud must be removed. Refer to → Rep. Gr.19; Radiator/Coolant Fan; Radiator, Removing and Installing.

A63-10411

Lower Front Longitudinal Member, Removing and Installing

Removing

- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".

- Remove the wheel spoiler. Refer to → Chapter "Front Wheel Spoiler, Removing and Installing".

- Remove the bolts -arrows- and the front lower longitudinal member -1-.

Installing

Install in reverse order of removal.

A10-11375