Chassis

General Information

~4min read
0102030405097N·mlb·ft
Tightening torque found on this page

Anti-Lock Braking System (ABS) Repair Information

ABS malfunctions do not affect the brake system and the booster. The conventional brake system remains operative even without ABS. A change in braking behavior should be checked. When the ABS indicator lamp comes on, the rear wheels can lock up early when braking.

WARNING

  • The ABS is always maintenance-free.
  • Testing, assembly, and repair work may only be performed by qualified personnel.
  • By not observing the points described in the repair manual, the system can be damaged and vehicle safety could be compromised.

Vehicles with high-voltage system

WARNING

Pay attention to the general warnings when working on a high-voltage system. Refer to → Electrical System Hybrid; Rep. Gr.93; High-Voltage System General Warnings.

All Vehicles

  • Before servicing the ABS system, determine the cause of the damage using OBD.
  • When installing a new hydraulic control module, the coding must be checked using the Vehicle Diagnostic Tester.
  • Disconnect the battery ground cable when the ignition is switched off.
  • When handling brake fluid, observe the relevant safety precautions and notes. Refer to → Chapter "General Information, Brake Fluid".
  • Bleed the brake system with the Brake Charger/Bleeder Unit -VAS5234- for all work that requires opening the hydraulic system. High and low pressure testing should also be performed on the brake system. Refer to → Chapter "Leak Test".
  • During the final road test, ensure that a ABS-controlled braking is performed at least once (pulsation must be felt at the brake pedal). Use the Vehicle Diagnostic Tester.

Component Location Overview

Overview - ABS/ESP

Overview - ABS/ESP

1 - Right Rear ABS Wheel Speed Sensor -G44-

  • Checking using the Vehicle Diagnostic Tester in Guided Fault Finding
  • Overview. Refer to → Chapter "Overview - Rear Axle Speed Sensor".

2 - Left Rear ABS Wheel Speed Sensor -G46-

  • Checking using the Vehicle Diagnostic Tester in Guided Fault Finding
  • Overview. Refer to → Chapter "Overview - Rear Axle Speed Sensor".

3 - Sensor Electronics Control Module -J849-

  • Component location: under the center console extension
  • Checking using the Vehicle Diagnostic Tester in Guided Fault Finding
  • Removing and installing. Refer to → Chapter "Sensor Electronics Control Module, Removing and Installing".

4 - Brake Lamp Switch -F-

  • Component location: on the brake pedal
  • Removing and installing. Refer to → Chapter "Brake Lamp Switch, Removing and Installing".

5 - Brake Pedal

  • Overview. Refer to → Chapter "Overview - Brake Pedal".

6 - Diagnostic Connection

  • Component location. Refer to → Fig. "Diagnostic connection component location".

7 - Left Front ABS Wheel Speed Sensor -G47-

  • Checking using the Vehicle Diagnostic Tester in Guided Fault Finding
  • Overview. Refer to → Chapter "Overview - Front Axle Speed Sensor".

8 - ABS Hydraulic Unit -N55- with ABS Control Module -J104-

  • The hydraulic unit and control module form the hydraulic control unit.
  • Overview. Refer to → Chapter "Overview - Control Module and Hydraulic Unit".

9 - Steering Column Electronics Control Module -J527-

  • With Airbag Spiral Spring/Return Spring with Slip Ring -F138- and Steering Angle Sensor -G85-
  • Removing and installing. Refer to → Electrical Equipment; Rep. Gr.94; Steering Column Switch Module; Steering Column Electronics Control ModuleJ527, Removing and Installing.

10 - Return Ring

  • Installed location: installed on the steering column with the slip ring

11 - Right Front ABS Wheel Speed Sensor -G45-

  • Checking using the Vehicle Diagnostic Tester in Guided Fault Finding
  • Overview. Refer to → Chapter "Overview - Front Axle Speed Sensor".

12 - -AUTO HOLD- Button -E540-

  • Component location: in the center console
  • Removing and installing. Refer to → Electrical Equipment; Rep. Gr.96; Controls; Electromechanical Parking Brake ButtonE538/-AUTO HOLD- ButtonE540, Removing and Installing.

13 - Electromechanical Parking Brake Button -E538-

  • Component location: in the center console
  • Removing and installing. Refer to → Electrical Equipment; Rep. Gr.96; Controls; Electromechanical Parking Brake ButtonE538/-AUTO HOLD- ButtonE540, Removing and Installing.

Diagnostic connection component location

  • Component location: the diagnostic connection for the Vehicle Diagnostic Tester is located in the driver side footwell.
A00-10303

Sensor Electronics Control Module -J849- Tightening Specification

- Tighten the nuts -1- to 9 N·m

A45-10124

Brake Pedal Position Sensor -G100- - Tightening Specification

- Tighten the bolts -arrows- to 8 N·m.

A46-10165