Chassis

Sensors

~7min read
0102030405097N·mlb·ft
Tightening torque found on this page

Overview - Front Axle Speed Sensor

Overview - Front Axle Speed Sensor

1 - Wheel Bearing Housing

2 - Bolt

  • 9 N·m

3 - Speed Sensor

  • Right Front ABS Wheel Speed Sensor -G45-/Left Front ABS Wheel Speed Sensor -G47-
  • Removing and installing. Refer to → Chapter "Right/Left Front ABS Wheel Speed Sensor -G45-/-G47-, Removing and Installing".

4 - Bolt

  • Tightening specification. Refer to → Suspension, Wheels, Steering; Rep. Gr.40; Wheel Bearing; Overview - Wheel Bearing.

5 - Wheel Bearing Unit

  • The ABS sensor ring is integrated in the wheel bearing unit

Overview - Rear Axle Speed Sensor

Overview - Rear Axle Speed Sensor, FWD Vehicles

Overview - Rear Axle Speed Sensor, FWD Vehicles

1 - Wheel Bearing Housing

2 - Speed Sensor

  • Right Rear ABS Wheel Speed Sensor -G44-/Left Rear ABS Wheel Speed Sensor -G46-
  • Removing and installing. Refer to → Chapter "Right/Left Rear ABS Wheel Speed Sensor -G44-/-G46-, Removing and Installing".

3 - Bolt

  • 9 N·m

4 - Front Seal

5 - Wheel Bearing Unit

  • The ABS sensor ring is integrated in the wheel bearing unit

6 - Bolt

  • Tightening specification. Refer to → Suspension, Wheels, Steering; Rep. Gr.42; Wheel Bearing and Trailing Arm; Overview - Wheel Bearing.

7 - Dust Cap

Overview - Rear Axle Speed Sensor, AWD Vehicles

Overview - Rear Axle Speed Sensor, AWD Vehicles

1 - Wheel Bearing Unit

  • The ABS sensor ring is integrated in the wheel bearing unit

2 - Wheel Bearing Housing

3 - Bolt

  • Tightening specification. Refer to → Suspension, Wheels, Steering; Rep. Gr.42; Wheel Bearing and Trailing Arm; Overview - Wheel Bearing.

4 - Speed Sensor

  • Right Rear ABS Wheel Speed Sensor -G44-/Left Rear ABS Wheel Speed Sensor -G46-
  • Removing and installing. Refer to → Chapter "Right/Left Rear ABS Wheel Speed Sensor -G44-/-G46-, Removing and Installing".

5 - Bolt

  • 9 N·m

Brake Lamp Switch, Removing and Installing

Special tools and workshop equipment required

  • Release Tool for Brake Light Switch -T40168A-

Component location: on the brake pedal

Removing

- Remove the driver side footwell vent. Refer to → Heating, Ventilation and Air Conditioning; Rep. Gr.87; Air Guide; Driver Side Footwell Vent, Removing and Installing.

- Disconnect the connector -2- from the Brake Lamp Switch -F-.

- Press the brake lamp switch piston -1- in completely with a finger -arrow A-.

- To release the brake lamp switch, turn the rotating piece -3-, with the piston pressed, counter-clockwise -B arrows- until it stops

- Disengage the piston from the released brake lamp switch.

A45-10169

- Insert the Release Tool for Brake Light Switch -T40168A- between the brake lamp switch piston and the brake pedal, as shown in the illustration.

  • The tool taper -1- must face the driver seat The opening on the tool must align with the projection on the brake lamp switch.

- Press the Release Tool for Brake Light Switch -T40168A- against the Brake Lamp Switch. The three tabs on the brake lamp switch unlock at the same time.

- Pull the Brake Lamp Switch -F--item 3- out of the mount -2-.

Installing

Install in reverse order of removal and note the following:

  • The brake push rod must be engaged with the brake pedal.
  • When installing the switch the brake pedal must not be operated.
A45-10170

- Insert the Brake Lamp Switch -F- into the mount -1- on the brake pedal.

  • The Brake Lamp Switch -F- must audibly engage with all three tabs.
  • Do not turn the Brake Lamp Switch -F- once it is inside the mount on the brake pedal.
  • The piston aligns itself automatically when inserting.

- To attach the brake lamp switch, turn the rotating piece -2- clockwise until it stops -arrows-.

Further installation is performed in reverse order of removal, while noting the following:

- Install the driver side footwell vent. Refer to → Heating, Ventilation and Air Conditioning; Rep. Gr.87; Air Guide; Driver Side Footwell Vent, Removing and Installing.

Note

Make sure the brake lamp switch is working correctly before driving the vehicle for the first time.

A45-10171

Brake Pedal Position Sensor, Removing and Installing

Note

Vehicles with a high-voltage system additionally have a Brake Pedal Position Sensor -G100-.

Removing

- Remove the driver side footwell vent. Refer to → Heating, Ventilation and Air Conditioning; Rep. Gr.87; Air Guide; Driver Side Footwell Vent, Removing and Installing.

- Disconnect the connector -1-.

- Remove the bolts -arrows- and the Brake Pedal Position Sensor -G100--item 2-.

Installing

Install in reverse order of removal and note the following:

- Install the driver side footwell vent. Refer to → Heating, Ventilation and Air Conditioning; Rep. Gr.87; Air Guide; Driver Side Footwell Vent, Removing and Installing.

A46-10165

Sensor Electronics Control Module, Removing and Installing

Special tools and workshop equipment required

  • Torque Wrench 1331 5-50Nm -VAG1331-

Note

If the Sensor Electronics Control Module -J849- is being replaced, select the "Replace" function for the Sensor Electronics Control Module -J849- on the Vehicle Diagnostic Tester in Guided Functions.

Removing

The Sensor Electronics Control Module -J849- is installed under the center console cover.

- Remove the center console cover. Refer to → Body Interior; Rep. Gr.68; Center Console; Overview - Center Console.

- Disconnect the connector -3-.

- Remove all four nuts -1-.

- Remove the Sensor Electronics Control Module -J849--2-.

Installing

Install in reverse order of removal and note the following:

Caution

Risk of destroying the Sensor Electronics Control Module -J849-.

Protect the Sensor Electronics Control Module -J849- from bumps or impact: A Sensor Electronics Control Module -J849- that has fallen to the ground can no longer be used.

- Mount the Sensor Electronics Control Module -J849- on the four bolts.

Note

Make sure it is in the correct installation position. The connector faces the direction of travel.

A45-10124

- Ensure a stress-free seating on the mounting.

Note

To install the Sensor Electronics Control Module -J849--item 2- free of tension, install all the nuts -1- loosely and then tighten them diagonally.

- Install the center console cover. Refer to → Body Interior; Rep. Gr.68; Center Console; Overview - Center Console.

- If the Sensor Electronics Control Module -J849- is being replaced, select the "Replace" function for the Sensor Electronics Control Module -J849- on the Vehicle Diagnostic Tester in Guided Functions.

A45-10124

Right/Left Front ABS Wheel Speed Sensor -G45-/-G47-, Removing and Installing

Special tools and workshop equipment required

  • Torque Wrench 1332 40-200Nm -VAG1332-
  • Grease -G 000 650-

Note

The sensor ring/rotor is installed in the respective wheel bearing unit and cannot be replaced.

Removing

- Release and disconnect the connector on the speed sensor -1-.

- Remove the bolt -2-.

- Remove the speed sensor from the wheel bearing housing.

Installing

Install in reverse order of removal and note the following:

- Before inserting speed sensor, clean hole inner surface and coat speed sensor all-round with Grease -G 000 650-.

- Insert the speed sensor and tighten.

- After installing, turn the steering all the way to the left and right, to make sure the speed sensor wiring has sufficient clearance.

A45-10094

Right/Left Rear ABS Wheel Speed Sensor -G44-/-G46-, Removing and Installing

Special tools and workshop equipment required

  • Torque Wrench 1332 40-200Nm -VAG1332-
  • Grease -G 000 650-

Note

The sensor ring/rotor is installed in the respective wheel bearing unit and cannot be replaced.

Removing

FWD Vehicles:

- Release and disconnect the connector on the speed sensor -1-.

- Remove the bolt -2-.

- Remove the speed sensor from the wheel bearing housing.

A45-10234

AWD vehicles:

- Release and disconnect the connector on the speed sensor -1-.

- Remove the bolt -2-.

- Remove the speed sensor from the wheel bearing housing.

Installing

Install in reverse order of removal and note the following:

- Before inserting speed sensor, clean hole inner surface and coat speed sensor all-round with Grease -G 000 650-.

- Insert the speed sensor and tighten.

A45-10095