Drive Shaft and Axle
Specifications
In this manual: Drive Shaft and Axle
~3min read
Specification
| Items | Inner side | Outer side | |
| Front Driveshaft | Connection Type | LSJ #104 | Minet #104C |
| Max. Allowable Angle | 23° | 45° | |
| Rear Driveshaft | Connection Type | CJ#79 | CJ#79 |
| Max. Allowable Angle | 23° | ||
| Rear Differential | Oil Type | API GL-5 Hypoid Gear Oil, SAE 75W/85 (SK HCT-5 Transmission Oil 75W/85 EQUIVALENT) |
|
| Oil Capacity | 0,70 ± 0.1 L | ||
| Gear Type | Hypoid | ||
| Differential Gear Ratio | 3.091 | ||
| Hypoid Gear Backlash | 0.07–0.15 mm (0.0028–0.0059 in.) | ||
| Differential Gear Backlash | 0.01–0.06 mm (0–0.0023 in.) | ||
Tightening Torque
| Items | N·m | kgf·m | lb-ft | |
| Front | Wheel Hub Nut | 88,3 - 107,9 | 9,0 - 11,0 | 65,1 - 79,6 |
| Drive Shaft Seal Nut | 294,2 - 313,8 | 30,0 - 32,0 | 217,0 - 231,5 | |
| Strut Assembly Lower Mounting Bolt | 137,2 - 156,9 | 14,0 - 16,0 | 101,2 - 115,7 | |
| Brake Caliper Mounting Bolt | 78,4 - 98,0 | 8,0 - 10,0 | 57,8 - 72,3 | |
| Wheel speed sensor mounting bolt | 6,9 - 10,8 | 0,7 - 1,1 | 5,1–8,0 | |
| Brake Disc Mounting Screw | 4,9 - 5,9 | 0,5 - 0,6 | 3,6 - 4,3 | |
| Hub Assembly Mounting Bolt | 78,4 - 98,0 | 8,0 - 10,0 | 57,8 - 72,3 | |
| Stabilizer Bar Upper Link Bolt | (A) 107.9 - 125.5 | 11,0 - 13,0 | 79,6 - 94,0 | |
| (B) 49.0 - 63.7 | 5,0 - 6,5 | 36,2 - 47,0 | ||
| Lower Arm Ball Joint Mounting Bolt | 98,1 - 117,7 | 10,0 - 12,0 | 72,3 - 86,8 | |
| Tie Rod End Ball Joint Mounting Nut | 34,3 - 44,1 | 3,5 - 4,5 | 25,3 - 32,5 | |
| Rear | Wheel Hub Nut | 88,3 - 107,9 | 9,0 - 11,0 | 65,1 - 79,6 |
| Drive Shaft Seal Nut | 294,2 - 313,8 | 30,0 - 32,0 | 217,0 - 231,5 | |
| Shock Absorber Lower Mounting Nut | 137,2 - 156,9 | 14,0 - 16,0 | 101,2 - 115,7 | |
| Brake Caliper Mounting Bolt | 49,0 - 58,8 | 5,0–6,0 | 36,2 - 43,4 | |
| Wheel speed sensor mounting bolt | 6,9 - 10,8 | 0,7 - 1,1 | 5,1–8,0 | |
| Brake Disc Mounting Screw | 4,9 - 5,9 | 0,5 - 0,6 | 3,6 - 4,3 | |
| Hub Assembly Mounting Bolt | 78,5 - 88,3 | 8,0 - 9,0 | 57,9 - 65,1 | |
| Upper Arm Mounting Bolt | 2WD: 137,2–156,9 | 14,0 - 16,0 | 101,2 - 115,7 | |
| All Wheel Drive: 98.1–117.7 | 10,0 - 12,0 | 72,3 - 86,8 | ||
| Lower Arm Mounting Bolt | 137,2 - 156,9 | 14,0 - 16,0 | 101,2 - 115,7 | |
| Auxiliary Arm Ball Joint Mounting Nut | 137,2 - 156,9 | 14,0 - 16,0 | 101,2 - 115,7 | |
| Trailing Arm Mounting Bolt | 34,3 - 53,9 | 3,5 - 5,5 | 25,3 - 39,7 | |
| Propeller Shaft |
Front Propeller Shaft Bolt | 49,0 - 68,6 | 5,0–7,0 | 36,2 - 50,6 |
| Propeller Shaft Center Bearing Bracket Mounting Bolt | 49,0 - 68,6 | 5,0–7,0 | 36,2 - 50,6 | |
| Rear Differential | Rear Propeller Shaft Bolt | 49,0 - 68,6 | 5,0–7,0 | 36,2 - 50,6 |
| Rear Differential Mounting Bolt | 68,6 - 88,3 | 7,0 - 9,0 | 50,6 - 65,1 | |
| Differential Cover Bolt | 39,2 - 49,0 | 4,0–5,0 | 28,9 - 36,2 | |
| Rear Differential Drain Plug | 49,0 - 68,6 | 5,0–7,0 | 36,2 - 50,6 | |
| Rear Differential Filler Plug | 39,2 - 58,8 | 4,0–6,0 | 28,9 - 43,3 | |
Lubricants
| Items | Lubricants | Quantity | Notes | ||
| Front Driveshaft | Minet #104C | R 2.2 | RBA | 125 ± 10/0 g | - |
| Lambda 3.8 GDI | RBA | 125 ± 10/0 g | - | ||
| Lambda 3.5 MPI | RBA | 125 ± 10/0 g | - | ||
| LSJ # 104 | R 2.2 | SH06-VX21 | 250 ± 10/0 g | TPE boot | |
| 250 ± 10/0 g | CR load | ||||
| Lambda 3.8 GDI | SH06-VX21 | 250 ± 10/0 g | TPE boot | ||
| 250 ± 10/0 g | CR load | ||||
| Lambda 3.5 MPI | SH06-VX21 | 250 ± 10/0 g | TPE boot | ||
| 250 ± 10/0 g | CR load | ||||
| Rear Driveshaft | CJ79 | GRB006 | 60 ± 10/0 g | - | |
| CJ79 | GRB006 | 60 ± 10/0 g | - | ||
Test yourself
A quick Hyundai Palisade quiz: every answer comes with an explanation and a link to the manual page.
Was this page helpful?