Hyundai Tucson LM Quiz
Body (Interior and Exterior)

Front Seat Belt Repair Procedures

In this manual: Body (Interior and Exterior)
General Information — 1Engine Mechanical System — 44Engine Electrical System — 45Emission Control System — 24Engine Control System/Fuel System — 93Clutch System — 13Manual Transmission — 18Automatic Transmission — 87Four-Wheel Drive (4WD) System — 26Drive Shaft and Axle — 29Suspension System — 35Steering — 20Restraints — 47Brake System — 36Body (Interior and Exterior) — 53Body Electrical System — 202Heating, Ventilation, and Air Conditioning — 58
22steps
~132min
4/5difficulty
02040608010053.940N·mlb·ft
Tightening torque found on this page
Done 0 of 22

Replacement

Front Seat Belt Replacement [General]
  • When installing the seat belt, take care not to damage the pretensioner.
  1. First remove the following items:
    A. Front door scuff trim (Refer to Interior - "Interior Trim")
    B. Rear Door Scuff Trim (Refer to Body Interior - "Interior Trim")
  2. Lift the lower anchor cover (A), then loosen the lower anchor mounting bolt (B).

    Tightening torque: 39.2 ~ 54 N·m

  3. Remove the center lower pillar trim (A).
  4. Remove the cap.
  5. Loosen the mounting bolt, then remove the upper center pillar trim (A).
  6. Loosen the mounting bolt, then remove the upper anchor (A).

    Tightening torque: 39.2 ~ 54 N·m

  7. After disconnecting the pretensioner connector lock pin, disconnect the pretensioner connector (B), loosen the mounting bolt, then remove the pretensioner (A).

    Tightening torque: 39.2 ~ 54 N·m

  8. Install in the reverse order of removal.
Front Seat Belt Replacement [Europe]
  • When installing the seat belt, take care not to damage the pretensioner.
  1. First remove the following items:
    A. Front door scuff trim (Refer to Interior - "Interior Trim")
    B. Rear Door Scuff Trim (Refer to Body Interior - "Interior Trim")
  2. Using a screwdriver or trim remover (B), remove the lower anchor (A).
  3. Remove the center lower pillar trim (A).
  4. Remove the cap.
  5. Loosen the mounting bolt, then remove the upper center pillar trim (A).
  6. Loosen the mounting bolt, then remove the upper anchor (A).

    Tightening torque: 39.2 ~ 54 N·m

  7. After disconnecting the pretensioner connector lock pin, disconnect the pretensioner connector (B), loosen the mounting bolt, then remove the pretensioner (A).

    Tightening torque: 39.2 ~ 54 N·m

  8. Install in the reverse order of removal.
  9. First remove the following items:
    A. Front door scuff trim (Refer to Interior - "Interior Trim")
    B. Rear Door Scuff Trim (Refer to Body Interior - "Interior Trim")
    C. Front Seat Belt Lower Anchor
    D. Front Seat Belt Upper Anchor
    E. Lower center pillar trim (Refer to Interior - "Interior Trim")
    F. Upper center pillar trim (Refer to Interior - "Interior Trim")
  10. Loosen the mounting bolt, then remove the height adjuster (A).

    Tightening torque: 39.2 ~ 54 N·m

  11. Install in the reverse order of removal.
    • Replace any damaged clips.
    • Make sure the height is adjusted correctly.
  12. Remove the front seat. (Refer to Seat and Power Seat - "Front Seat")
  13. Loosen the mounting bolt and remove the front seat belt buckle (A).

    Tightening torque: 39.2 ~ 54 N·m

  14. Install in the reverse order of removal.
Height Adjuster Replacement, Front Seat Belt Buckle Replacement

Test yourself

A quick Hyundai Tucson LM quiz: every answer comes with an explanation and a link to the manual page.