Body Electrical System

Air Ventilation Seat Repair procedures

30steps
~180min
4/5difficulty
Done 0 of 30

Removal

[Ventilation Blower]

  1. Disconnect the negative (-) battery terminal.

  2. Remove the front seat assembly.

    (Refer to Body - "Front Seat Assembly")

  3. Disconnect the ventilation blower connector (A).

  4. Remove the ventilation blower ducts (A) after removing the screw and clips.

  5. Remove the blower fan (A) after removing the screws.

[Ventilation Seat Unit]

  1. Disconnect the negative (-) battery terminal.

  2. Remove the assist front seat assembly.

    (Refer to Body - "Front Seat Assembly")

  3. Remove the front seat cushion cover.

    (Refer to Body - "Front Seat Cushion Cover")

  4. Remove the front seat cushoin panel (A) after loosening the mounting bolts.

  5. Disconnect the ventilation seat unit connectors (A).

  6. Remove the ventilation seat unit (A) after loosening the mounting screws.

Installation

[Ventilation Blower]

  1. Install the blower fan.

  2. Install the blower duct.

  3. Install the front seat assembly.

  4. Connect the negative (-) battery terminal.

[Ventilation Seat Unit]

  1. Install the ventilation seat unit.

  2. Install the front seat cushion panel.

  3. Install the front seat cushion cover.

  4. Install the assist front seat assembly.

  5. Connect the negative (-) battery terminal.

Inspection

Ventilation Seat Diagnostic Mode

Ventilated seat is largely composed of seat ventilation unit for control, switch for input and blower for output.

The diagnostic mode for checking normal operation of these three components has the following functions.

  1. Operate seat heater switch to enter diagnostic mode.

  2. Enter diagnostic mode by referring to below timing chart and explanation.

  3. Press seat heater switch as below.

    1. Press seat heater switch for over 3 seconds.

    2. Release the switch for less than 3 seconds, and press again for 1.5-3 seconds.

    3. Release the switch for less than 3 seconds, and press again for over 3 seconds.

  4. Diagnostic mode will start immediately after 3 LED lamps of seat heater switch (Low, Mid, High) blink once.

    1. In self-diagnostic mode, only the seat heater switch LED lamps will operate.

    2. If two or more errors are detected, the lamps will blink in sequence with intervals of 2 seconds for each error code.

  5. After entering diagnostic mode, check LED blinking status to check errors.

    Failure Indication Blinking of LED Inspection Item Cause of Failure
    Detect low voltage




    Low voltage compared to operating voltage range

    Detect over voltage




    Over voltage compared to operating voltage range

    Disconnected fuse Disconnected B+ fuse
    Disconnected IGN2 fuse
    Short in NTC/HEATER MAT
    1. Faulty NTC element

    2. Disconnected heater mat

    3. Disconnected heater + wiring

    4. Disconnected heater system NTC (Over 4.9V)

    Short in NTC/HEATER MAT
    1. Short between controller connector terminal and NTC

    2. Short between controller connector terminal and heater

    3. Short in heater system NTC wiring

    4. Short in heater system heater + wiring

    Detect loss of temperature Target temperature not reached in 40 minutes
    Disconnected ventilation blower power Disconnected blower power wiring
    Short in ventilation blower power Short in blower power wiring
    Disconnected ventilation blower speed signal Disconnected blower speed signal
    Short in ventilation blower speed signal Short in ventilation blower speed signal (VCC)
    Short in ventilation blower speed signal Short in ventilation blower speed signal (GND)
    Disconnected ventilation blower rpm signal




    isconnected ventilation blower rpm signal
    Short in ventilation blower rpm signal




    Short in ventilation blower rpm signal (VCC)
    Short in ventilation blower rpm signal Short in ventilation blower rpm signal
  6. Inspect cause of failure indicated by LED status.

  7. Trouble code will be recorded by seat ventilation unit.

  8. When the passenger side seat heater switch is pressed for over 5 seconds, the LED will blink 4 times and trouble code will be deleted.

  9. Switch "OFF" ignition to exit diagnostic mode of ventilated seat.

  10. Switch "ON" ignition and check that seat ventilation system works properly. To check trouble code, refer to step 2 again.