Body Electrical System

Seat Heater Repair procedures

12steps
~72min
3/5difficulty
Done 0 of 12

Inspection

Front Seat Heater

  1. Check for continuity and measure the resistance between terminals No 3 and No 6.

    Standard value

    Driver / Assists (cushion + back)

    Heater seat : 1.77?±10%/23 °C

    Ventilated seat : 1.93?±10%/23 °C

  2. Operate the seat heater after connecting the connector, and then check the thermostat by measuring the temperature of seat surface.

    Standard value

    1st : cushion : 36±2 °C, back : 40±2 °C

    2st : cushion : 39±2 °C, back : 45±2 °C

    3st : cushion : 42±2 °C, back : 50±2 °C

Rear Seat Heater

  1. Check for continuity and measure the resistance between terminals No 1 and No 4.

    Standard value Rear seat (Cushion only) : 3.16?±10%/23 °C

  2. Operate the seat heater after connecting the connector, and then check the thermostat by measuring the temperature of seat surface.

    Standard value High (Cushion) : 38±2 °C Low (Cushion) : 42±2 °C

Seat Heater Unit Diagnostic Mode

  1. Enter diagnostic mode by operating the seat heater switch.

  2. Enter diagnostic mode by referring to the below description.

    • Keep pressing the seat heater switch for over 3 seconds and release the switch. Then, within 2 seconds, press the switch again for over 3 seconds.

    • When diagnostic mode is entered, all switch LEDs will blink once.

  3. After entering diagnostic mode, check cause of failure according to blinking or illumination of LEDs.

    [Driver Side / Passenger Side Seat Heater]

    1st Row Seat Heater Unit

    Failure Indication Inspection Item Cause of Failure
    Low : OFF
    Mid : OFF
    High : FLASHING
    Detect low voltage
    • IGN1 power below 8.5V

    Detect over voltage
    • IGN1 power below 16.5V

    Low : FLASHING
    Mid : FLASHING
    High : FLASHING
    Broken fuse
    • B (+) fuse disconnected

    Low : OFF
    Mid : ON
    High : FLASHING
    Disconnected / Short NTC
    • NTC element defective

    • Short between NTC connector terminals

    • NTC (+) wiring disconnected

    • NTC (-) wiring disconnected

    Low : FLASHING
    Mid : FLASHING
    High : FLASHING
    Disconnected / Short heater
    • Heater element defective

    • Short between heater unit connector terminals

    • Heater (+) wiring disconnected

    • Heater (-) wiring disconnected

    Low : ON
    Mid : ON
    High : FLASHING
    Detect loss of temperature
    • If target temperature is not reached within 40 minutes


    2nd Row Seat Heater Unit

    Failure Indication Inspection Item Cause of Failure
    Low : OFF
    High : OFF
    Detect low voltage
    • IGN1 power below 8.5V

    Detect over voltage
    • IGN1 power below 16.5V

    Low : FLASHING
    High : FLASHING
    Broken fuse
    • B (+) fuse disconnected

    Low : OFF
    High : FLASHING
    Disconnection/Short in NTC
    • NTC element defective

    • Short between NTC connector terminals

    • NTC (+) wiring disconnected

    • NTC (-) wiring disconnected

    Low : FLASHING
    High : FLASHING
    Disconnection/Short in heater
    • Heater element defective

    • Short between heater unit connector terminals

    • Heater (+) wiring disconnected

    • Heater (-) wiring disconnected

    Low : ON
    High : FLASHING
    Detect loss of temperature
    • If target temperature is not reached within 40 minutes

  4. Check the defective area by the blinking pattern of LED lamps.

  5. Error is recorded by the seat heater unit.

  6. Error memory can be deleted by pressing the seat heater switch for over 5 seconds with the LED lamps blinking four times.

  7. Switching "OFF" the ignition will end the diagnostic mode for seat heater unit.

  8. Switch "ON" the ignition and check that seat heater system operates properly. To check the error code, refer to step 2 above.