Cruise Control & Driver Assistance

Action Test

29steps
~174min
5/5difficulty
Done 0 of 29

Work Procedure

After repairing the malfunction symptom of ProPILOT Assist 2.1, perform an operation check of ProPILOT Assist 2.1 and check that ProPILOT Assist 2.1 operates normally.

CHECK FOR ProPILOT ASSIST SWITCH

  1. Start the engine.

  2. Press the ProPILOT Assist switch (less than 1.5 seconds).

    Information display status
    ProPILOT Assist 2.1 status indicator : ON (gray)
    Set distance indicator : Long mode (gray)
    Set vehicle speed indicator :

    “———”

    “MPH”
  3. Check that the vehicle information display in the combination meter is in the set standby status.

  4. Press ProPILOT Assist switch and check that ProPILOT Assist 2.1 operating lamp turns OFF when ProPILOT Assist 2.1 is turned OFF.

  5. When the engine starts again, make sure that ProPILOT Assist 2.1 operating lamp is OFF.

>>

GO TO 2.

CHECK FOR DISTANCE SWITCH

  1. Start the engine.

  2. Press the ProPILOT Assist switch (less than 1.5 seconds).

  3. Press the DISTANCE switch.

  4. Check that the set distance indicator changes display in order of: (Long)→(Middle)→(Short).

>>

GO TO 3.

CHECK FOR RES+, SET-, AND CANCEL SWITCHES

  1. Check that RES+, SET-, CANCEL switches are operated smoothly.

  2. Check that switches come up as hand is released from the switches.

>>

GO TO 4.

SET CHECKING (1)

  1. Start the engine.

  2. Press the ProPILOT Assist switch (less than 1.5 seconds) and turn the ProPILOT Assist 2.1 system ON.

  3. Drive the vehicle at desired vehicle speed between 30 km/h and 120 km/h.

  4. Push down the SET- switch.

  5. Check that the desired speed is set and ProPILOT Assist 2.1 control starts when releasing SET- switch.

>>

GO TO 5.

CHECK FOR INCREASE OF CRUISING SPEED (1)

  1. Set desired vehicle speed between 30 km/h and 120 km/h.

  2. Check that the set vehicle speed increases when RES+ switch is pushed up.

>>

GO TO 6.

CHECK FOR DECREASE OF CRUISING SPEED (1)

  1. Set desired vehicle speed between 30 km/h and 120 km/h.

  2. Check that the set vehicle speed is reduced when SET- switch is pushed down.

>>

GO TO 7.

SET CHECKING (2)

  1. Stop the vehicle.

  2. Drive the vehicle at less than approximately 30 km/h.

  3. Push down the SET- switch when the system detects a vehicle ahead.

  4. When releasing finger, check that vehicle-to-vehicle distance is controlled to keep proper distance from vehicle ahead according to the vehicle speed, up to vehicle speed of 30 km/h approximately.

>>

GO TO 8.

CHECK FOR INCREASE OF CRUISING SPEED (2)

  1. Set the ProPILOT Assist 2.1 when the vehicle speed is less than approximately 30 km/h and when a vehicle ahead is detected.

  2. Check that the set vehicle speed increases when RES+ switch is pushed up.

>>

GO TO 9.

CHECK FOR DECREASE OF CRUISING SPEED (2)

  1. Set the ProPILOT Assist 2.1 when the vehicle speed is less than approximately 30 km/h and when a vehicle ahead is detected.

  2. Set the set vehicle speed to the desired vehicle speed according to “check for increase of cruising speed”.

  3. Check that the set vehicle speed is reduced when SET- switch is pushed down.

>>

GO TO 10.

CHECK THE BLUE INDICATOR OF ProPILOT ASSIST 2.1 DISPLAY

Check that the ProPILOT Assist 2.1 indicator is turned blue when driving on highways or motorways with HD maps.

However, in the following cases, the indicator is not turned blue.

  • When driving beyond the speed detected by the sign detection function

  • When approaching to tollhouses, exits, junctions, intersections, or lanes reduction points nearby

  • When no GPS signal is received

  • When driving on a road that is not separated from the oncoming lane

  • When the wiper is operating at low speed or high speed

  • When judging that the driver does not hold or operate the steering wheel

  • When judging that the driver is not facing forward

  • When accelerating by depressing the accelerator pedal

  • When the approach warning is activated

  • When the lane departure warning is activated

>>

GO TO 11.

CHECK FOR CANCELLATION OF ProPILOT ASSIST 2.1

Check that the ProPILOT Assist 2.1 is canceled when performing the following operations.

  • When the brake pedal is depressed after ProPILOT Assist 2.1 is set and the vehicle is driven.

  • When the shift position is in the “N” position after ProPILOT Assist 2.1 is set and the vehicle is driven.

  • When the ProPILOT Assist switch is turned OFF after ProPILOT Assist 2.1 is set and the vehicle is driven.

  • When the CANCEL switch is pressed after ProPILOT Assist 2.1 is set and the vehicle is driven.

>>

GO TO 12.

CHECK THAT THE SET vehicle SPEED RETURN TO THE SAME AS BEFORE CANCELLATION

Check that the vehicle restores the previous speed kept before the system deactivation when performing the following operations.

  • Drive the vehicle when the ProPILOT Assist 2.1 is set and depress the brake pedal to cancel the control. Check that the vehicle restores the previous vehicle speed kept before the system deactivation when pushing up the RES+ switch.

  • Drive the vehicle when the ProPILOT Assist 2.1 is set and shift the shift position to the “N” position to cancel the control. Check that the vehicle restores the previous vehicle speed kept before the system deactivation when shifting the shift position to the “D” position and pushing up the RES+ switch.

  • Drive the vehicle when the ProPILOT Assist 2.1 is set and press the CANCEL switch to cancel the control. Check that the vehicle restores the previous vehicle speed kept before the system deactivation when pushing up the RES+ switch.

>>

INSPECTION END