Driver Information & Multimedia

Telematics

18steps
~108min
5/5difficulty
Done 0 of 18

Diagnosis and Repair Work Flow

Work Flow

OVERALL SEQUENCE

  • Reference 1··· Refer to Consult Function.

  • Reference 2··· Refer to DTC Index.

  • Reference 3··· Refer to Symptom Table.

DETAILED FLOW

INTERVIEW AND SYMPTOM CONFIRMATION

Check the malfunction symptoms by performing the following items.

  • Interview the customer to obtain the malfunction information (conditions and environment when the malfunction occurred).

  • Check the symptom.

Is the occurred symptom malfunction?

YES>>

GO TO 2.

NO>>

INSPECTION END

DIAGNOSIS WITH CONSULT

With CONSULT

  1. Connect CONSULT and perform a self-diagnosis for “IVC”. Refer to Consult Function.

  2. When DTC is detected, follow the instructions below:

    • Record DTC and Freeze Frame Data.

Are any DTCs displayed?

YES>>

GO TO 3.

NO>>

GO TO 4.

TROUBLE DIAGNOSIS FOR DTC

  1. Check the DTC indicated in the self-diagnosis results.

  2. Perform the relevant diagnosis referring to the DTC Index. Refer to DTC Index.

>>

GO TO 4.

PERFORM SYMPTOM DIAGNOSIS

Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to Symptom Table.

>>

GO TO 5.

ERROR PART REPAIR

With CONSULT

  1. Repair or replace the identified malfunctioning parts.

  2. Perform a self-diagnosis for “IVC” with CONSULT.

  3. Check that the symptom does not occur.

Does the symptom occur?

YES>>

GO TO 1.

NO>>

INSPECTION END

Additional Service When Replacing Tcu

Work Procedure

Description

When TCU is replaced, TCU configuration is required.

Preparation before configuration operation

  • Subscribe to telematics service.

  • Preregister user ID and password (can be performed from owner homepage).

  • Since VIN data is not included in the TCU after replacement, it is required to write VIN data with CONSULT.

Work Procedure

READING OF VIN DATA

WITH CONSULT

  1. Turn ignition switch ON and wait at least 5 seconds.

  2. Select “Save vehicle identification number data” of “Work support” item using CONSULT.

  3. Touch “Start” on “Save vehicle identification number data” screen to save the VIN data stored in replaced TCU in CONSULT.

>>

GO TO 2.

TCU REPLACEMENT

Replace TCU. Refer to Removal & Installation.

>>

GO TO 3.

PERFORM TCU CONFIGURATION

WITH CONSULT

Touch "Replace ECU" of CONSULT, Perform TCU configuration according to CONSULT.

Can VIN data be saved to CONSULT at 1st step?

YES>>

GO TO 4.

NO>>

GO TO 5.

AUTOMATIC WRITING OF VIN DATA TO TCU

WITH CONSULT

  1. Turn ignition switch ON and wait at least 5 seconds.

  2. Select “Write vehicle identification number (saved data)” of “Work support” item using CONSULT.

  3. Touch “Start” at “Write vehicle identification number (saved data)” screen to write the VIN data saved in CONSULT into new TCU.

>>

GO TO 6.

MANUAL WRITING OF VIN DATA TO TCU

WITH CONSULT

  1. Turn ignition switch ON and wait at least 5 seconds.

  2. Select “Write vehicle identification number (manual input)” of “Work support” item using CONSULT.

  3. Touch “Start” at “Write vehicle identification number (manual input)” screen to write the VIN data into new TCU.

>>

GO TO 6.

CHECK NETWORK INITIAL SETTINGS

WITH CONSULT

Select “Work Support” of “IVC” and perform “Network initial settings”.

>>

WORK END

Additional Service After Automatic Report

Work Procedure

Description

When the automatic report function of the TCU is activated, the TCU locks the automatic report function after the automatic report. Therefore, it is necessary to release the lock on the TCU after the automatic report function of the TCU is activated.

Work Procedure

AUTOMATIC REPORT PREVENTION RELEASE

CONSULT Work support

  1. Turn ignition switch ON.

  2. Select "Automatic report prevention release" to unlock the automatic report prevention.

>>

WORK END