Driver Information & Multimedia

Warning Chime System

8steps
~48min
4/5difficulty
Done 0 of 8

Precautions

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision.

Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual.

  • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, it is recommended that all maintenance and repair be performed by an authorized NISSAN/INFINITI dealer.

  • Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see “SRS AIR BAG”.

  • Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

  • When using air or electric power tools or hammers, always switch the ignition/power switch OFF, disconnect the 12V battery or batteries, and wait at least 3 minutes before performing any service.

Precautions for Removing Battery Terminal

  • When disconnecting the 12V battery terminal, turn off the ACC power before disconnecting the 12V battery terminal, observing “How to disconnect 12V battery terminal” described below.

  • For Nissan Armada vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON the ignition switch.

  • After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

HOW TO DISCONNECT 12V BATTERY TERMINAL

Disconnect 12V battery terminal according to instruction described below.

  1. Open the hood.

  2. Turn ignition switch to the ON position.

  3. Turn ignition switch to the OFF position with the driver side door opened.

  4. Get out of the vehicle and close the driver side door.

  5. Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse of the specified time.

    BR08DE : 4 minutes R9N engine : 12 minutes
    BR10DE : 12 minutes V9X engine : 4 minutes
    D4D engine : 20 minutes YD25DDTi : 2 minutes
    HR09DET : 12 minutes YS23DDT : 4 minutes
    HR10DDT : 12 minutes YS23DDTT : 4 minutes
    HR10DET : 12 minutes ZD30DDTi : 60 seconds
    HR13DDT : 12 minutes ZD30DDTT : 60 seconds
    HRA2DDT : 12 minutes K9K engine : 4 minutes
    M9R engine : 4 minutes R9M engine : 4 minutes
  6. Remove 12V battery terminal.

Diagnosis and Repair Workflow

Work Flow

OVERALL SEQUENCE

DETAILED FLOW

OBTAIN INFORMATION ABOUT SYMPTOM

Interview the customer to obtain as much information as possible about the conditions and environment under which the malfunction occurred.

>>

GO TO 2.

CHECK SYMPTOM

  • Check the symptom based on the information obtained from the customer.

  • Check if any other malfunctions are present.

>>

GO TO 3.

CHECK CONSULT SELF-DIAGNOSIS RESULTS

  1. Connect CONSULT and perform self-diagnosis. Refer to DTC Index

  2. When DTC is detected, follow the instructions below:

    • Record DTC and Freeze Frame Data.

Are self-diagnosis results normal?

YES>>

GO TO 4.

NO>>

GO TO 5.

NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS

Perform symptom diagnosis and narrow down the malfunctioning parts.

>>

GO TO 5.

REPAIR OR REPLACE MALFUNCTIONING PARTS

Repair or replace malfunctioning parts.

>>

GO TO 6.

FINAL CHECK

Check that the warning buzzer in the combination meter operates normally.

Does it operate normally?

YES>>

INSPECTION END

NO>>

GO TO 1.