Power Supply, Ground & Circuit Elements

Battery inspection

In this manual: Power Supply, Ground & Circuit Elements
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~6min read

How to Handle Battery

CAUTION:
• If it becomes necessary to start the engine with a booster battery and jumper cables, use a 12-volt booster battery. • After connecting battery cables, ensure that they are tightly clamped to battery terminals for good contact.

• Never add distilled water through the hole used to check specific gravity

.

METHODS OF PREVENTING OVER-DISCHARGE

The following precautions must be taken to prevent over-discharging a battery.

• The battery surface (particularly its top) should always be kept clean and dry. • The terminal connections should be clean and tight.

• At every routine maintenance, check the electrolyte level.

This also applies to batteries designated as “low maintenance” and “maintenance-free”.

• When the vehicle is not going to be used over a long period of

• When the vehicle is not going to be used over a long period of time, disconnect the battery cable from the negative terminal. (If the vehicle has an extended storage switch, turn it off.)

• Check the charge condition of the battery.

• Check the charge condition of the battery.

Periodically check the specific gravity of the electrolyte. Keep a close check on charge condition to prevent over-discharge.

CHECKING ELECTROLYTE LEVEL

CHECKING ELECTROLYTE LEVEL

WARNING:
Never allow battery fluid to come in contact with skin, eyes, fabrics, or painted surfaces. After touching a battery, never touch or rub your eyes until you have thoroughly washed your hands. If acid contacts eyes, skin or clothing, immediately flush with water for 15 minutes and seek medical attention. • Remove the cell plug using a suitable tool.

• Add distilled water up to the MAX level.

Sulphation

Sulphation
A battery will be completely discharged if it is left unattended for a long time and the specific gravity will become less than 1.100. This may result in sulphation on the cell plates.

To determine if a battery has been “sulphated”, note its voltage and current when charging it. As shown in the figure, less current and higher voltage are observed in the initial stage of charging sulphated batteries.

A sulphated battery may sometimes be brought back into service by means of a long, slow charge, 12 hours or more, followed by a battery capacity test.

SPECIFIC GRAVITY CHECK

SPECIFIC GRAVITY CHECK

1. Read hydrometer and thermometer indications at eye level.

2. Convert into specific gravity at 20 °C.

Example:
• When electrolyte temperature is 35 °C and specific gravity of electrolyte is 1.230, converted specific gravity at 20 °C is 1.240.

• When electrolyte temperature is 0 °C and specific gravity of electrolyte is 1.210, converted specific gravity at 20 °C is 1.196.


Work Flow

Work Flow

OVERALL SEQ

DETAILED FLOW

DETAILED FLOW

1.VISUAL INSPECTION 1. Check battery case for cracks or bends. 2. Check battery terminals for damage.

3. If the difference between the max. and min. electrolyte level in cells is within 10 mm (0.39 in), it is OK.

Are these inspection results normal? YES >> GO TO 2.

NO >> Replace battery.

2.CHECKING SPECIFIC GRAVITY

Check specific gravity. Refer to PG-111, "How to Handle Battery".

Inspection results Above 1.220 (Test using battery checker)>>GO TO 3.

Above 1.220 (Test using load tester)>>GO TO 5.

1.100 - 1.220 (When performing quick charge)>>GO TO 7.

1.100 - 1.220 (When performing standard charge)>>GO TO 12.

Below 1.100>>GO TO 13.

3.CAPACITY TEST

Test using battery checker.

Is the battery usable, according to the manufacturer’s instructions? YES >> Ready for use. Mount battery again and check loose terminals. Also check other related circuits.

NO >> GO TO 4.

4.QUICK CHARGE 1. Perform quick charge. Time required: 45 min. Refer to PG-122, "Quick Charge".

2. Test using battery checker.

Is the battery usable, according to the manufacturer’s instructions? YES >> Ready for use.

NO >> Replace battery.

5.CAPACITY TEST 1. Test using load tester.

2. Check battery type and determine the specified current using the table.

Discharging Current (Load Tester)

3. Read load tester voltage when specified discharging current flows through

3. Read load tester voltage when specified discharging current flows through battery for 15 seconds.

Is the voltage 9.6 V or more? YES >> Ready for use.

NO >> GO TO 6.

6.QUICK CHARGE 1. Perform quick charge. Time required: 45 min. Refer to PG-122, "Quick Charge".

2. Test using load tester.

Is the voltage 9.6 V or more? YES >> Ready for use.

NO >> Replace battery.

7. QUICK CHARGE 1. Perform quick charge. Refer to PG-122, "Quick Charge".

2. Perform capacity test.

Test using battery checker.>>GO TO 8.

Test using load tester.>>GO TO 10.

8.CAPACITY TEST

Test using battery checker.

Is the battery usable, according to the manufacturer’s instructions? YES >> Ready for use.

NO >> GO TO 9.

9.CHECKING SPECIFIC GRAVITY 1. Check specific gravity. Refer to PG-111, "How to Handle Battery".

2. Perform recharge. Refer to PG-122, "Quick Charge".

NOTE

:
If battery temperature rises above 55 °C, stop charging. Always charge battery when its temperature is below 55 °C.

3. Test using battery checker.

Is the battery usable, according to the manufacturer’s instructions? YES >> Ready for use.

NO >> Replace battery.

10.CAPACITY TEST 1. Test using load tester.

2. Check battery type and determine the specified current using the table.

Discharging Current (Load Tester)


3. Read load tester voltage when specified discharging current flows through

3. Read load tester voltage when specified discharging current flows through battery for 15 seconds.

Is the voltage 9.6 V or more? YES >> Ready for use.

NO >> GO TO 11.

11.CHECKING SPECIFIC GRAVITY 1. Check specific gravity. Refer to PG-111, "How to Handle Battery".

2. Perform recharge. Refer to PG-122, "Quick Charge".

NOTE

:
If battery temperature rises above 55 °C, stop charging. Always charge battery when its temperature is below 55 °C.

3. Test using load tester.

Is the voltage 9.6 V or more? YES >> Ready for use.

NO >> Replace battery.

12. STANDARD CHARGE NOTE

:
“STANDARD CHARGE” is recommended if the vehicle is in storage after charging.

1. Perform standard charge. Refer to PG-121, "Standard Charge".

2. Perform capacity test.

Test using battery checker.>>GO TO 14.

Test using load tester.>>GO TO 15.

13. SLOW CHARGE 1. Perform slow charge. Refer to PG-120, "Slow Charge".

2. Perform capacity test.

Test using battery checker.>>GO TO 14.

Test using load tester.>>GO TO 15.

14.CAPACITY TEST

Test using battery checker.

Is the battery usable, according to the manufacturer’s instructions? YES >> Ready for use.

NO >> Replace battery.

15.CAPACITY TEST 1. Test using load tester.

2. Check battery type and determine the specified current using the table.

Discharging Current (Load Tester)


3. Read load tester voltage when specified discharging current flows through

3. Read load tester voltage when specified discharging current flows through battery for 15 seconds.

Is the voltage 9.6 V or more? YES >> Ready for use.

NO >> Replace battery.