Heater & Air Conditioning Control System Type 1

Blower motor

In this manual: Heater & Air Conditioning Control System Type 1
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read

Diagnosis Procedure

1.CHECK FUSE 1. Turn ignition switch OFF.

2. Check following fuses.

- 10A fuse [No. 15, located in fuse block (J/B)] - 15A fuses [Nos. 14 and 16, located in fuse block (J/B)]

NOTE

:
Refer to PG-22, "Fuse, Connector and Terminal Arrangement".

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.

2.CHECK BLOWER MOTOR POWER SUPPLY 1. Disconnect blower motor connector. 2. Turn ignition switch ON.

3. Check voltage between blower motor harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 3.

3.CHECK BLOWER RELAY 1. Turn ignition switch OFF.

2. Check blower relay. Refer to HAC-82, "Component Inspection (Blower Relay)".

Is the inspection result normal? YES >> Repair harness or connector between blower motor and fuse.

NO >> Replace blower relay.

4.CHECK BLOWER MOTOR CONTROL CIRCUIT 1. Turn ignition switch OFF. 2. Connect blower motor connector. 3. Disconnect power transistor connector. 4. Turn ignition switch ON.

5. Check voltage between power transistor harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 5.

5.CHECK BLOWER MOTOR CONTROL CIRCUIT FOR OPEN 1. Turn ignition switch OFF. 2. Disconnect blower motor connector.

3. Check continuity between power transistor harness connector and blower motor harness connector.

Is the inspection result normal?

Is the inspection result normal? YES >> Replace blower motor. Refer to VTL-15, "Removal and Installation (LHD models)" or VTL-16, "Removal and Installation (RHD models)".

NO >> Repair harness or connector.

6.CHECK A/C AUTO AMP. IGNITION POWER SUPPLY 1. Turn ignition switch OFF. 2. Disconnect A/C auto amp. 3. Turn ignition switch ON.

4. Check voltage between A/C auto amp. harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair harness or connector between A/C auto amp. and fuse.

7.CHECK POWER TRANSISTOR IGNITION POWER SUPPLY

Check voltage between power transistor harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair harness or connector between power transistor and fuse.

8.CHECK POWER TRANSISTOR GROUND CIRCUIT FOR OPEN 1. Turn ignition switch OFF.

2. Check continuity between power transistor harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 9.

NO >> Repair harness or connector.

9.CHECK POWER TRANSISTOR CONTROL SIGNAL 1. Connect blower motor connector and A/C auto amp. connector. 2. Turn ignition switch ON. 3. Set air outlet to VENT.

4. Change fan speed from 1st – 7th, and check duty ratios between blower motor harness connector and ground by using an oscilloscope.

NOTE

:
Calculate the drive signal duty ratio as shown in the figure.

T2 = Approx. 1.6 ms

Is the inspection result normal?

Is the inspection result normal? YES >> Replace power transistor. Refer to HAC-97, "Removal and Installation".

NO >> GO TO 10.

10.CHECK POWER TRANSISTOR CONTROL SIGNAL CIRCUIT FOR OPEN 1. Turn ignition switch OFF. 2. Disconnect power transistor connector and A/C auto amp. connector.

3. Check continuity between power transistor harness connector and A/C auto amp. harness connector.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 11.

NO >> Repair harness or connector.

11.CHECK POWER TRANSISTOR CONTROL SIGNAL CIRCUIT FOR SHORT

Check continuity between power transistor harness connector and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> Replace A/C auto amp. Refer to HAC-91, "Removal and Installation".

NO >> Repair harness or connector.

Component Inspection (Blower Motor)

1.CHECK BLOWER MOTOR 1. Remove blower motor. Refer to VTL-15, "Removal and Installation (LHD models)" or VTL-16, "Removal and Installation (RHD models)".

2. Check that there is not any mixing foreign object in the blower motor.

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace blower motor. Refer to VTL-15, "Removal and Installation (LHD models)" or VTL-16, "Removal and Installation (RHD models)".

2.CHECK BLOWER MOTOR

Check that there is not breakage or damage in the blower motor.

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace blower motor. Refer to VTL-15, "Removal and Installation (LHD models)" or VTL-16, "Removal and Installation (RHD models)".

3.CHECK BLOWER MOTOR

Check that blower motor turns smoothly.

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace blower motor. Refer to VTL-15, "Removal and Installation (LHD models)" or VTL-16, "Removal and Installation (RHD models)"

Component Inspection (Blower Relay)

1.CHECK BLOWER RELAY 1. Remove blower relay. Refer to PG-22, "Fuse, Connector and Terminal Arrangement".

2. Check continuity between blower relay terminal 3 and 5 when the voltage is supplied between terminal 1 and 2.


Is the inspection result normal?

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace blower relay.