Brake System RHD

Brake pedal

In this manual: Brake System RHD
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~3min read
Inspection and Adjustment

INSPECTION

Brake Pedal Height
Check the height (H1) between the dash lower panel (1) and the brake pedal upper surface.

H1 : Refer to BR-136, "Brake Pedal".

CAUTION:
Remove the floor trim.
Stop Lamp Switch

Stop Lamp Switch
Check the clearance (C) among the brake pedal lever (1) and the stop lamp switch (2) threaded end.

C : Refer to BR-136, "Brake Pedal".

NOTE:

Pull the brake pedal pad to make the clearance between the stop lamp switch threaded end and the brake peal lever.

Brake Switch/Brake Pedal Position Switch

Brake Switch/Brake Pedal Position Switch Check the clearance (C) among the brake pedal lever (1) and the brake switch/brake pedal position switch (2) threaded end.

C : Refer to BR-136, "Brake Pedal".

NOTE

:
Pull the brake pedal pad to make the clearance between the brake switch/brake pedal position switch threaded end and the brake peal lever.

Brake Pedal Play

Brake Pedal Play
Press the brake pedal. Check the brake pedal play (A) (stroke until fluid pressure occurs).

A : Refer to BR-136, "Brake Pedal".

Depressed Brake Pedal Height

Depressed Brake Pedal Height Check the height between the dash lower panel (1) and the brake pedal upper surface (H2) when depressing the brake pedal at 490 N (50 kg, 110 lb) while turning engine ON.

H2 : Refer to BR-136, "Brake Pedal".

CAUTION:
Remove the floor trim.
ADJUSTMENT

ADJUSTMENT

Brake Pedal Height
1. Remove instrument lower panel. Refer to IP-13, "Removal and Installation". 2. Disconnect the stop lamp switch and brake switch/brake pedal position switch harness connector. 3. Loosen the stop lamp switch and brake switch/brake pedal position switch 45° counterclockwise. 4. Loosen the lock nut (2) of input rod (1).

5. Rotate the input rod, adjust the brake pedal to the specified height (H1).

CAUTION:
The threaded end of the input rod must project to the inner side (L) of the clevis (3).
H1 : Refer to BR-136, "Brake Pedal".

H1 : Refer to BR-136, "Brake Pedal".

6. Tighten the lock nut. Refer to BR-111, "Exploded View".

7. Adjust the clearance between the brake pedal lever and the stop lamp switch and brake switch/brake pedal position switch threaded end after adjusting the brake pedal height.

Stop Lamp Switch

Stop Lamp Switch
1. Remove instrument lower panel. Refer to IP-13, "Removal and Installation". 2. Disconnect the harness connector from stop lamp switch.

3. Loosen the stop lamp switch 45° counterclockwise.

4. Press-fit the stop lamp switch (2) until the stop lamp switch hits the brake pedal lever (1) 45° clockwise while pulling the brake pedal pad slightly.

CAUTION:
• The clearance (C) between the brake pedal lever and stop lamp switch threaded and must be the specified value.

C : Refer to BR-136, "Brake Pedal".

• The stop lamp must be turned off when the brake pedal is released.
Brake Switch/Brake Pedal Position Switch

Brake Switch/Brake Pedal Position Switch 1. Remove instrument lower panel. Refer to IP-13, "Removal and Installation". 2. Disconnect the harness connector from brake switch/brake pedal position switch. 3. Loosen the brake switch/brake pedal position switch 45° counterclockwise.

4. Press-fit the brake switch/brake pedal position switch (2) until the brake switch/brake pedal position switch hits the brake pedal lever (1) 45° clockwise while pulling the brake pedal pad slightly.

CAUTION:
The clearance (C) between the brake pedal lever and brake switch/brake pedal position switch threaded and must be the specified value.

C : Refer to BR-136, "Brake Pedal".

Depressed Brake Pedal Height

Depressed Brake Pedal Height 1. Perform the air bleeding. Refer to BR-81, "Bleeding Brake System".

2. Check the height between the dash lower panel (1) and the brake pedal upper surface (H2) when depressing the brake pedal at 490 N (50 kg, 110 lb) while turning engine ON.

H2 : Refer to BR-136, "Brake Pedal".

CAUTION:
Remove the floor trim.
Brake fluid