Instrument Panel

Center console assembly

In this manual: Instrument Panel
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read

Exploded View

CVT models

1. Console indicator finisher

1. Console indicator finisher 2. Instrument lower cover RH 3. Center console assembly 4. Instrument lower cover LH 5. Instrument stay
6. CVT shift selector assembly 7. Console rear bracket 8. Console rear finisher 9. Seat heated switch
10. Console switch finisher 11. Console switch finisher 12. Console finisher assembly 13. Console mask
14. Console front bracket

: Metal clip: Pawl
MT model: Metal clip


MT model

1. Console boot

1. Console boot
2. Instrument lower cover RH 3. Center console assembly 4. Instrument lower cover LH 5. Instrument stay
6. Console center bracket 7. Console rear bracket 8. Console rear finisher 9. Seat heated switch
10. Console switch finisher 11. Console switch finisher 12. Console finisher assembly 13. Console mask
14. Console front bracket

: Metal clip: Pawl
Removal and Installation: Metal clip


Removal and Installation

WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or more.

REMOVAL

CAUTION:
When removing, always use a remover tool that is made of plastic.
1. Remove shift lever knob (MT models only). • 5MT models: Refer to TM-25, "Removal and Installation".

• 6MT models: Refer to TM-78, "Removal and Installation".

2. Remove console finisher assembly.

1. Put selector lever in “N” position. 2. Loosen the parking brake lever stroke by turning the adjusting nut with a socket wrench. Refer to PB- 2, "Inspection and Adjustment". 3. Lift up console finisher assembly in numerical order shown in the figure and disengage metal clips.

4. Remove console finisher assembly while pulling it towards vehicle rear.

: Metal clip

CAUTION:: Metal clip


CAUTION:
• Be careful not for damaging parts in surrounding area.

• Remove metal clips slowly so that they are not damaged.

3. Remove console rear finisher.

1. Put front seat assembly (LH and RH) to frontmost position.

2. Pull back console rear finisher, and disengage the pawls and metal clips.

: Metal clip: Pawl
: Metal clip


4. Remove center console assembly fixing screws (A).

4. Remove center console assembly fixing screws (A).

5. Remove instrument lower cover LH.

5. Remove instrument lower cover LH.

1. Put front seat assembly LH to rearmost position. 2. Remove fixing clip (A).

3. Pull the instrument lower cover LH crosswise, and disengage the pawl and metal clips.

CAUTION:
Remove pawl and metal clips slowly so that they are not damaged.

: Metal clip: Pawl
: Metal clip


6. Remove instrument lower cover RH.

6. Remove instrument lower cover RH.

1. Put front seat assembly RH to rearmost position. 2. Remove fixing clip (A).

3. Pull the instrument lower cover RH crosswise, and disengage the pawl and metal clips.

CAUTION:
Remove pawl and metal clips slowly so that they are not damaged.

: Metal clip: Pawl
: Metal clip


7. Remove center console assembly.

7. Remove center console assembly.

1. Remove center console fixing screws (A).

1. Remove center console fixing screws (A).

2. Lift up center console assembly back side.

CAUTION:
Be careful not for damaging parts in surrounding area.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:
After installation, adjust the parking brake lever stroke. Refer to PB-2, "Inspection and Adjustment".

Disassembly and Assembly

Disassembly and Assembly of Console Finisher Assembly

CAUTION:
When disassembling, always use a remover tool that is made of plasti

c.

DISASSEMBLY

1. Remove console finisher assembly. Refer to IP-23, "Removal and Installation".

2. Remove console indicator finisher (CVT models)

Disengage connection of the console indicator finisher (2) fixing pawls from the inside of the console finisher assembly (1) toward the outside, and remove.

: Pawl


3. Remove console indicator finisher (MT models)

3. Remove console indicator finisher (MT models)

Disengage connection of the console boot (2) fixing pawls from the inside of the console finisher assembly (1) toward the outside, and remove.

: Pawl


4. Remove console switch finisher.

4. Remove console switch finisher.

Disengage connection of the console switch finisher (2) fixing pawls from the inside of the console finisher assembly (1) toward the outside, and remove.

NOTE

:
Remove seat heated switch. Refer to SE-51, "Removal and Installation".

: Pawl


ASSEMBLY

ASSEMBLY

Assemble in the reverse order of disassembly.