Instrument Panel

Instrument panel assembly

In this manual: Instrument Panel
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~10min read

Exploded View

LHD models

1. Front passenger air bag module

1. Front passenger air bag module 2. Instrument panel assembly 3. Instrument side finisher LH 4. Combination meter
5. Cluster lid A
6. Push-button ignition switch 7. Steering column upper cover 8. Steering lock escutcheon 9. Steering column lower cover 10. Multi display unit
11. Instrument lower cover LH 12. Instrument lower cover RH 13. Instrument under cover RH 14. Glove box dumper
15. Glove box assembly
16. Instrument side finisher RH 17. Sunload sensor
18. Switch panel
19. Hazard switch
20. Instrument lower panel LH 21. Audio unit or AV C/U 22. Cluster lid C
23. Warning lamp
24. Glove box lid
25. Front passenger air bag OFF switch 26. Socket knob
27. Inner socket
28. Socket ring
29. Cluster tray
30. USB connector
31. Instrument under cover LH 32. A/C controller (manual A/C) 33. A/C finisher (manual A/C) 34. Knob (manual A/C)
35. Instrument under cover RH (RHD models)

: Pawl: Clip
: Metal clip: Pawl
: Do not reuse: Metal clip
: N·m (kg-m, ft-lb): Do not reuse
Removal and Installation: N·m (kg-m, ft-lb)


Removal and Installation

WORK STEP

When removing instrument panel assembly, combination meter, AV C/U, or center console assembly take steps in the order shown by the numbers below.


[ ]: Number indicates step in removal procedure.

[ ]: Number indicates step in removal procedure.

WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or more

.

REMOVAL

CAUTION:
When removing, always use a remover tool that is made of plastic.
1. Remove shift lever knob (MT models only). • 5MT models: Refer to TM-25, "Removal and Installation".

• 6MT models: Refer to TM-78, "Removal and Installation".

2. Remove console finisher assembly.

1. Put selector lever in “N” position. 2. Loosen the parking brake lever stroke by turning the adjusting nut with a socket wrench. Refer to PB- 2, "Inspection and Adjustment". 3. Lift up console finisher assembly in numerical order shown in the figure and disengage metal clips.

4. Remove console finisher assembly while pulling it towards vehicle rear.

: Metal clip

CAUTION:: Metal clip


CAUTION:
• Be careful not for damaging parts in surrounding area.

• Remove metal clips slowly so that they are not damaged.

5. Disconnect seat heated switch harness connectors (with seat heated switch).

3. Remove console rear finisher.

1. Put front seat assembly (LH and RH) to frontmost position.

2. Pull back console rear finisher, and disengage the pawls and metal clips.

: Metal clip: Pawl
: Metal clip


4. Remove center console assembly fixing screws (A).

4. Remove center console assembly fixing screws (A).

5. Remove instrument lower cover LH.

5. Remove instrument lower cover LH.

1. Put front seat assembly LH to rearmost position. 2. Remove fixing clip (A).

3. Pull the instrument lower cover LH crosswise, and disengage the pawl and metal clips.

CAUTION:
Remove pawl and metal clips slowly so that they are not damaged.

: Metal clip: Pawl
: Metal clip


6. Remove instrument lower cover RH.

6. Remove instrument lower cover RH.

1. Put front seat assembly RH to rearmost position. 2. Remove fixing clip (A).

3. Pull the instrument lower cover RH crosswise, and disengage the pawl and metal clips.

CAUTION:
Remove pawl and metal clips slowly so that they are not damaged.

: Metal clip: Pawl
: Metal clip


7. Remove center console assembly.

7. Remove center console assembly.

1. Remove center console fixing screws (A).

2. Remove seat heated switch harness clip (with seat heated switch).

2. Remove seat heated switch harness clip (with seat heated switch).

3. Lift up center console assembly back side.

CAUTION:
Be careful not for damaging parts in surrounding area.
8. Release front pillar portion of front body side welt LH. Refer to INT-20, "BODY SIDE WELT : Removal and Installation". 9. Remove front pillar garnish LH. Refer to INT-18, "FRONT PILLAR GARNISH : Removal and Installation".

10. Remove instrument side finisher LH.

1. Insert remover tool (A) between instrument side finisher LH and instrument panel assembly to disengage the pawls as shown in the figure.

2. Pull back instrument side finisher LH.

CAUTION:: Pawl


CAUTION: Apply protective tape (B) on the part to protect it from damage.
11. Remove instrument under cover LH.

11. Remove instrument under cover LH.

1. Remove fixing clips (A).

2. Pull downward and disengage pawls.

: Pawl


NOTE:

NOTE:
RHD models 1. Remove fixing clips (A). 2. Remove fixing clip (B).

3. Pull downward and disengage pawls.

: Pawl


12. Remove instrument lower panel LH.

12. Remove instrument lower panel LH.

1. Remove hood opener and fuel lid opener lever. Refer to DLK-173, "HOOD LOCK CONTROL CABLE : Removal and Installation". 2. Remove fixing screw (A). 3. Pull back instrument lower panel LH, and then disengage the pawls and metal clips.

4. Disconnect harness connectors and aspirator duct.

: Metal clip: Pawl
: Metal clip


13. Remove driver air bag module. Refer to SR-13, "Removal and

13. Remove driver air bag module. Refer to SR-13, "Removal and Installation". 14. Remove steering wheel. Refer to ST-9, "Removal and Installation".

15. Remove steering column covers.

1. Place the tilt to the lowest level. 2. Remove steering lock escutcheon (1). (without Intelligent Key)
3. Remove fixing screws (A). 4. Pull up steering column upper cover (2), and then disengage steering column upper cove fixing pawls. 5. Remove steering column upper cover.

6. Pull down the steering column lower cover (3), and then remove steering column lower cover.

NOTE: Pawl


NOTE

:
Disengage the pawls, and then remove steering lock escutcheon (4). (with Intelligent Key)

16. Remove spiral cable. Refer to SR-16, "Removal and Installation".

16. Remove spiral cable. Refer to SR-16, "Removal and Installation". 17. Remove combination switch. Refer to BCS-94, "Removal and Installation".

18. Remove cluster lid A.

1. Cover steering shaft with a shop cloth (A) to prevent damage. 2. Pull back cluster lid A while holding the lower side and disengage the metal clips underside. 3. Hold both upper sides of cluster lid A and pull it out towards vehicle rear, and disengage pawl and metal clips topside.

4. Disconnect push-button ignition switch harness connector and NATS antenna amp.harness connector. (with Intelligent Key)

: Metal clip: Pawl
: Metal clip


CAUTION:

CAUTION:
Remove metal clips slowly so that they are not damaged.
19. Remove combination meter. Refer to MWI-69, "Removal and Installation".

20. Remove multi display unit (with auto A/C) or A/C finisher (with manual A/C).

Multi display unit (with auto A/C)

Multi display unit (with auto A/C) A/C finisher (with manual A/C)

: Metal clip: Pawl
• Multi display unit (with auto A/C): Metal clip


• Multi display unit (with auto A/C) - Insert a remover tool (A) between multi display unit (1) and instrument panel assembly (2), and then disengage pawls and metal clip.

- Pull back multi display unit, and then disconnect harness connector.

CAUTION:
Apply protective tape (B) on the part to protect it from damage.
• A/C finisher (with manual A/C) - Remove intake door lever knob (3). Refer to HAC-239, "Removal and Installation". - Insert a remover tool (A) between A/C finisher (4) and instrument panel assembly (5), and then disengage pawls and metal clip.

- Pull back A/C finisher.

CAUTION:
Apply protective tape (B) on the part to protect it from damage.
21. Remove A/C control fixing screws (with Manual A/C). Refer to HAC-239, "Removal and Installation".

22. Remove cluster lid C.

1. Remove fixing screws (A). 2. Pull back cluster lid C, and disengage the pawls and metal clips.

3. Disconnect harness connector.

: Metal clip: Pawl
: Metal clip


23. Remove audio or NAVI control unit.

23. Remove audio or NAVI control unit. • Audio unit: Refer to AV-38, "Removal and Installation".

• NAVI control unit: Refer to AV-84, "Removal and Installation".

24. Disconnect hazard switch harness connector.

25. Remove cluster tray.

1. Insert a remover tool (A) between cluster tray and instrument panel assembly, and then pull downward and disengage metal clips. 2. Pull back cluster tray.

3. Disconnect harness connectors.

CAUTION:: Metal clip


CAUTION:
Apply protective tape (B) on the part to protect it from damage.
26. Release front pillar portion of front body side welt RH. Refer to INT-20,

26. Release front pillar portion of front body side welt RH. Refer to INT-20, "BODY SIDE WELT : Removal and Installation". 27. Remove front pillar garnish RH. Refer to INT-18, "FRONT PILLAR GARNISH : Removal and Installation".

28. Remove instrument side finisher RH.

1. Insert remover tool (A) between instrument side finisher RH and instrument panel assembly to disengage the pawls as shown in the figure.

2. Pull back instrument side finisher RH.

CAUTION:: Pawl


CAUTION:
Apply protective tape (B) on the part to protect it from damage.
29. Remove instrument under cover RH.

29. Remove instrument under cover RH.

1. Remove fixing clips (A).

2. Pull downward and disengage pawl and metal clips.

: Metal clip Pawl
: Metal clip


30. Remove glove box lid.

30. Remove glove box lid.

1. Open glove box lid.

2. Pull glove box lid (1) toward vehicle rear, and then disengage the joint from instrument panel assembly (2).

3. Disengage the pawl, and then remove damper pin on right

3. Disengage the pawl, and then remove damper pin on right side.

CAUTION:: Pawl


CAUTION:
Never excessively pull string of glove box damper.
31. Remove glove box assembly.

31. Remove glove box assembly.

2WD models

2WD models
4WD models

1. Remove fixing screws (A).

2. Pull back the glove box cover assembly while holding the lower side and disengage the pawls.

32. Remove front passenger air bag module. Refer to SR-19, "Removal and: Pawl


32. Remove front passenger air bag module. Refer to SR-19, "Removal and Installation".

33. Remove switch panel. 1. Insert remover tool (A) between switch panel and instrument panel assembly to disengage the pawls as shown in the figure.

2. Pull up switch panel, and then disconnect harness connector.

CAUTION:: Pawl


CAUTION:
Apply protective tape (B) on the part to protect it from damage.
34. Remove instrument panel assembly mounting screws (A) and bolts (B).

34. Remove instrument panel assembly mounting screws (A) and bolts (B).

CAUTION:
Cover tool with a shop cloth to prevent windshield glass from being damaged.

35. Remove instrument panel assembly.

1. Disengage harness (A) and harness (B) of front pillar LH and RH portions from instrument panel assembly.

2. Remove instrument panel from passenger door opening portion.

CAUTION:
• Cover CVT shift selector upper surface with a shop cloth to prevent it from being damaged.

• When removing instrument panel assembly, 2 workers are required to prevent it from dropping.

36. Remove the following parts after removing instrument panel assembly.

• Side defrostor nozzle: Refer toVTL-10, "SIDE DEFROSTER NOZZLE : Removal and Installation". • Side ventilator grille: Refer to VTL-11, "SIDE VENTILATOR GRILLE : Removal and Installation". • Side defrostor grille: VTL-11, "SIDE DEFROSTER GRILLE : Removal and Installation". • Front defrostor nozzle: VTL-11, "FRONT DEFROSTER NOZZLE : Removal and Installation". • Center ventilator duct: VTL-12, "CENTER VENTILATOR DUCT : Removal and Installation". • Side ventilator duct: VTL-12, "SIDE VENTILATOR DUCT : Removal and Installation". • GPS antenna: AV-89, "Removal and Installation".

• Hazard switch: EXL-97, "Removal and Installation".

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:
After installation, adjust the parking brake lever stroke. Refer to PB-2, "Inspection and Adjustment".