Engine Control System K9K

Diagnosis and repair workflow

In this manual: Engine Control System K9K
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~6min read

Work Flow

OVERALL SEQUENCE

• Malfunctions are declared as either present or stored (depending on whether

• Malfunctions are declared as either present or stored (depending on whether they appeared in a certain context and have disappeared since, or whether they remain present but have not been diagnosed within the current context). • The present or stored status of malfunctions should be taken into consideration when the diagnostic tool is used following the + after ignition supply being switched on (without acting on the system components). • For a present malfunction, apply the procedure described in the Interpretation of malfunction section. • For a stored malfunction, note the malfunctions displayed and apply the instructions in the Notes section.

• If the malfunction is confirmed when the instructions in the Notes section are applied, the malfunction is present. Deal with the malfunction • If the malfunction is not confirmed, check: - the electrical lines which correspond to the malfunction, - the connectors for these lines (for oxidation, bent pins, etc), - the condition of the wires (insulation has melted or been cut, abrasions), - the resistance of the component detected as malfunction.

Conformity Check
• The aim of the conformity check is to check data that does not produce a malfunction on the diagnostic tool because the data is inconsistent. Therefore, this phase is used to: - carry out malfunction finding on malfunctions that do not have a malfunction display, and which may correspond to a customer complaint.

- check that the system is operating correctly and that there is no risk of a malfunction recurring after repairs.

• This section gives the malfunction finding procedures for statuses and parameters and the conditions for checking them.

• If a status is not behaving normally or a parameter is outside the permitted tolerance values, consult the corresponding malfunction finding page.

Customer Complaints - Malfunction finding chart If the test with the diagnostic tool is OK but the customer complaint is still present, the malfunction should be processed by customer complaint.

NOTE

:
A synopsis of the general procedure to follow is provided on the preceding page in the form of a flow chart.

Malfunction Finding Procedure (Wiring Check) Diagnostics malfunctions Removing the connectors and/or handling the wirings may temporarily remove the origin of a DTC. The measurements of the electrical voltages, resistance and insulation are generally correct, especially when the DTC is not present at the time of the analysis (stored DTC).

Visual Check
Look for impacts under the bonnet and in the passenger compartment.

Perform a careful check of the protections, insulation and correct running of wirings.

Look for traces of oxidation.

Tactile Check
While manipulating the wirings, use the diagnostic tool to detect a change in DTC status from ???stored??? to ???present???.

Ensure that the connectors are correctly engaged.

Apply light stresses to the connectors.

Gently manipulate the wiring harness.

If a change of status occurs, try to isolate the origin of the incident.

Inspection of each component Disconnect the connectors and check the appearance of the clips and blades and their crimping (no crimping on the insulating part).

Check that the clips and blades are properly engaged in the receptacles.

Ensure that there is no rebounding of clips or blades at the time of connection.

Check the contact pressure of the clips using a suitable model blade.

Resistance Control
Test the continuity of the lines in their entirety, then section by section.

Try to create a short-circuit to earth, on the + 12 V or with another wire.

If a DTC is detected, repair or replace the wiring.

REMINDERS

Trouble Diagnosis:

There are present DTCs and stored DTCs (which appeared in a certain context and have since disappeared or which are still present but have not had trouble diagnosis performed on them in the current context).

The ???present??? or ???stored??? status of DTCs must be considered when activating the diagnostic tool after power is supplied to the ECM (without activating the system components).

Deal with present DTCs according to the procedure specified in the corresponding DTC trouble diagnosis.

For stored DTCs, note the DTCs displayed and follow the instructions in the Notes section.

If the DTC is confirmed when the instructions in the Notes section are applied, the malfunction is present. Deal with the DTC.

If the DTC is not confirmed, check: • Electrical lines which correspond to the malfunction • Connectors for these lines (for oxidation, bent pins, etc.) • Resistance of the malfunction component • Condition of the wires (melted or cut insulation, wear)

Conformity Check
The conformity check is designed to check the states and data monitor items which do not display any DTCs on the diagnostic tool when inconsistent. This phase therefore allows: • Diagnoses malfunctions that do not have a DTC display, and which may correspond to a customer complaint.

• Checks that the system is operating correctly and that there is no risk of a DTC reappearing after repairs.

This section gives the trouble diagnosis procedures for states and parameters and the conditions for checking them.

If a state is not operating normally or a data monitor value is outside permitted tolerance values, you should consult the corresponding trouble diagnosis page.

Customer Complaints - Trouble Diagnosis If the test with the CONSULT-III is OK, but the customer complaint still present, the malfunction should be treated by customer complaints.

A synopsis of the general procedure to follow is provided on the previous page in the form of a flow chart.

SAFETY ADVICE

• The safety instructions must be followed at all times when working on components, to avoid damage or injury:
- make sure that the battery is properly charged to avoid damaging the computers with a low load,
- use the appropriate tools, - do not touch the xenon bulbs.

Diagnostic Work Sheet

DESCRIPTION

There are many operating conditions that lead to the malfunction of engine components. A good grasp of such conditions can make troubleshooting faster and more accurate.

In general, each customer feels differently about a incident. It is important to fully understand the symptoms or conditions for a customer complaint.

Utilize a diagnostic worksheet like the one on the next page in order to organize all the information for troubleshooting.

Some conditions may cause the MI to come on steady or blink and DTC to be detected. Examples: • Vehicle ran out of fuel, which caused the engine to misfire.

• Fuel filler cap was left off or incorrectly screwed on, allowing fuel to evaporate into the atmosphere.

WORKSHEET SAMPLE

WORKSHEET SAMPLE

Basic inspection