Engine Lubrication System K9K

Engine oil

In this manual: Engine Lubrication System K9K
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~3min read

Inspection

OIL LEVEL AND MUDDINESS

• Before starting the engine, check the oil level placing vehicle horizontally.

If the engine is already started, stop it and allow 10 minutes before checking. • Make sure the oil level is within the range shown in the figure.

• If it is out of range, adjust it.

ENGINE OIL APPEARANCE

ENGINE OIL APPEARANCE

• Check engine oil for white turbidity or heavy contamination.

• If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.

Repair or replace damaged parts.

OIL LEAKAGE

Check for oil leakage around the following area.

• Oil pan
• Oil pan drain plug
• Oil pressure switch
• Oil filter bracket
• Vacuum pump
• Oil pump housing
• Mating surface between cylinder block and cylinder head • Mating surface between cylinder head and rocker cover • Oil cooler
• Crankshaft oil seals

OIL PRESSURE CHECK

WARNING:
• Be careful not to burn yourself, as the engine oil is hot.

• Oil pressure check should be done in Neutral “N” position.

1. Check the oil level. Refer to “OIL LEVEL MUDDINES“. 2. Remove engine undercover.

3. Disconnect harness connector at oil pressure switch (1), and remove oil pressure switch using a deep socket (commercial service tool).

2 : Oil pan : Vehicle front

CAUTION:
Never drop or shock oil pressure switch.
4. Install oil pressure gauge [SST:KV113E0020 (Mot. 836-05)]

4. Install oil pressure gauge [SST:KV113E0020 (Mot. 836-05)] 5. After warming up the engine, make sure oil pressure corresponding to the engine speed is produced.

Engine oil pressure : Refer to LU-39, "Standard and Limit".

6. After checking, install the oil pressure switch as follows.

a. Remove old liquid gasket adhering to the switch and engine.

b. Apply liquid gasket and tighten oil pressure switch to specification.

Use Genuine Liquid Gasket or equivalent.

Tightening torque : Refer to LU-35, "Exploded View".

7. Start engine and check for oil leakage.

Draining

WARNING:
• Be careful not to get burned, as engine oil may be hot.

• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.

1. Warm up the engine, and check for engine oil leakage from engine components. Refer to LU-25, "Inspection". 2. Stop the engine and wait for 10 minutes. 3. Loosen oil filler cap.

4. Remove drain plug and then drain engine oil.

Refilling

1. Refill with new engine oil.

Engine oil specification and viscosity: Refer to MA-13, "Fluids and Lubricants".

Engine oil capacity : Refer to LU-39, "Standard and Limit".

CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifications for reference only.

• Always use oil level gauge to determine the proper amount of engine oil in the engine.

2. Warm up engine and check area around drain plug and oil filter for engine oil leakage. 3. Stop engine and wait for 10 minutes.

4. Check the engine oil level. Refer to LU-33, "Inspection".