Engine Cooling System HR16DE

Radiator

In this manual: Engine Cooling System HR16DE
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read

Exploded View

1. Reservoir tank hose

1. Reservoir tank hose 2. Mounting rubber (upper) 3. Radiator tank cap
4. Radiator
5. Mounting rubber (lower) 6. O-ring
7. Drain plug
8. Clamp
9. Radiator hose (lower) 10. Cooling fan assembly 11. Radiator hose (upper) 12. Reservoir tank
13. Reservoir tank cap

A. To water outlet
B. To water inlet
C. To water inlet

disassembly.: Always replace after every
disassembly.

Removal and Installation: N·m (kg-m, in-lb)


Removal and Installation

REMOVAL

WARNING:
• Never remove radiator cap when engine is hot. Serious burns may occur from high-pressure engine coolant escaping from radiator.

• Wrap a thick cloth around the radiator cap. Slowly turn it a quarter of a turn to release built-up pressure.

Then turn it all the way.

1. Drain engine coolant from radiator. Refer to CO-37, "Draining".

CAUTION:
• Perform this step when the engine is cold.

• Never spill engine coolant on drive belt.

2. Remove air duct (inlet). Refer to EM-161, "Exploded View". 3. Remove reservoir tank as follows: a. Disconnect reservoir tank hose. b. Release the tab (A) in the direction shown by the arrow ().
).

c. Lift up and remove the reservoir tank with tab released.

4. Remove radiator hose (upper and lower).

4. Remove radiator hose (upper and lower). 5. Disconnect harness connector from fan motor, and move harness aside.

6. Remove cooling fan assembly.

CAUTION:
Be careful not to damage or scratch the radiator core.

7. Remove the following parts.

• Front grille assembly. Refer to EXT-18, "Removal and Installation".

• Front bumper fasica assembly. Refer to EXT-13, "Removal and Installation" • Front combination lamp assembly (LH and RH). Refer to EXL-91, "Removal and Installation".

8. Remove radiator core support (upper). Refer to DLK-147, "HR16DE : Removal and Installation" (WITH IKEY &SUPER LOCK) or DLK-310, "HR16DE : Removal and Installation" (WITH I-KEY WITHOUT SUPER LOCK) orDLK-445, "HR16DE : Removal and Installation" (WITHOUT I-KEY &WITH SUPER LOCK) DLK- 561, "HR16DE : Removal and Installation" (WITHOUT I-KEY & SUPER LOCK).

9. Remove the radiator (1) from bottom of the vehicle.

2 : Condenser assembly CAUTION:: Vehicle front


CAUTION:
Be careful not to damage radiator core and condenser assembly core.

INSTALLATION

Install in the reverse order of removal.

Radiator
NOTE

:
When installing radiator core support (upper), check that both upper and lower mounts of radiator and air conditioner condenser are inserted in the mounting holes of radiator core support (upper, lower).

(Breakage prevention for radiator) Reservoir tank
NOTE:
• Insert reservoir tank straight into the mounting location and check by the feel that the pawl is securely fastened.

• Pull reservoir tank upward to check that it does not come off.

Radiator hose
NOTE

:
Insert the radiator hose (1) all the way to the stopper (2) or by 33 mm (1.30 in) (hose without a stopper).

Unit: mm (in)

Unit: mm (in)
A. Radiator side
B. Engine side

• For the orientation of the hose clamp pawl, refer to the figure.

*: Refer to the illustrations for the specific position each hose clamp tab.

*: Refer to the illustrations for the specific position each hose clamp tab.

E. View E f. 45° g, 45°

E. View E f. 45° g, 45° • The angle (b) created by the hose clamp pawl and the specified: Vehicle upper


• The angle (b) created by the hose clamp pawl and the specified line (A) must be within ±30 as shown in the figure.

• To install hose clamps (1), check that the dimension (A) from the

• To install hose clamps (1), check that the dimension (A) from the end of the hose clamp on the radiator hose to the hose clamp is within the reference value.

Dimension “A” : (−1) – (+1) mm

Inspection

Inspection

INSPECTION AFTER INSTALLATION

• Check for leakage of engine coolant using the radiator cap tester adapter (commercial service tool) and the radiator cap tester (commercial service tool). Refer to CO-37, "Inspection".

• Start and warm up the engine. Check visually that there is no leakage of engine coolant.